Dell S320 Command List

pdmAudio
pdmAudioBalanc
e
.1.3.6.1.4.1.2699.2.4.1.16.6.0 Integer
R DEFVAL { 0 }
pdmAlert pdmAlertIndex 1.3.6.1.4.1.2699.2.4.1.18.1.1.1.1 Integer
not-accessible
1
pdmAlert
pdmAlertGroupT
ype
1.3.6.1.4.1.2699.2.4.1.18.1.1.2.1 String R See Note 1
pdmAlert
pdmAlertGroupI
d
1.3.6.1.4.1.2699.2.4.1.18.1.1.3.1 String R See Note 1
pdmAlert pdmAlertCode 1.3.6.1.4.1.2699.2.4.1.18.1.1.4.1 String R DEFVAL { "" }
pdmAlert
pdmAlertDescrip
tion
1.3.6.1.4.1.2699.2.4.1.18.1.1.5.1 String R
Alert's condition has lamp
Fail, Lamp hours running out,
Projector Overheating, Lamp
Overheating and Fan Error.
pdmAlert
pdmAlertSeverity
Level
1.3.6.1.4.1.2699.2.4.1.18.1.1.6.1 Integer
R See Note 1
pdmAlert
pdmAlertTrainin
gLevel
1.3.6.1.4.1.2699.2.4.1.18.1.1.7.1 Integer
R DEFVAL { 2 }
pdmAlert
pdmAlertDateTi
me
1.3.6.1.4.1.2699.2.4.1.18.1.1.8.1 String R
DEFVAL
{ "1980-01-01T00:00:00" }
pdmAlert
pdmAlertPowerO
nCount
1.3.6.1.4.1.2699.2.4.1.18.1.1.9.1 String R DEFVAL { "" }
pdmAlert
pdmAlertSysUpti
me
1.3.6.1.4.1.2699.2.4.1.18.1.1.10.1 String R DEFVAL { "" }
pdmAlert
pdmAlertCritical
AlertsCount
1.3.6.1.4.1.2699.2.4.1.18.2.0 Integer
R
pdmAlert
pdmAlertAllAlert
sCount
1.3.6.1.4.1.2699.2.4.1.18.3.0 Integer
R
Note 1:
a) If there is no any current alert, all of OID in alert table will respond default value.
pdmAlertGroupType =” “
pdmAlertGroupID = 0
pdmAlertSeverity = other (1)
The reset Object will respond default.
b) If there is FAN alert happen, the tables is shown below.
pdmAlertGroupType =” Fan”
pdmAlertGroupID = “Fan Error”
pdmAlertSeverity = Critical (3)
The rest Object will respond default.
c) If there is Lamp fail alert happen, the tables is shown below.
pdmAlertGroupType = “Lamp”
pdmAlertGroupID= Lamp Fail
pdmAlertSeverity = Critical (3)
The rest Object will respond default.
d) If there is Lamp hours running out alert happen, the tables is shown below.
pdmAlertGroupType = “Lamp”
pdmAlertGroupID= Lamp hours running out
pdmAlertSeverity = warning (4)
The rest Object will respond default.
e) If there is Projector Over-heating alert, the tables is shown below.
pdmAlertGroupType = “ThermalSensor”
pdmAlertGroupID= “Projector Overheating”
pdmAlertSeverity = warning (4)
The rest Object will respond default.
f) If there is Lamp Over-heating alert, the tables is shown below.
pdmAlertGroupType = “ThermalSwitch”
pdmAlertGroupID= “Lamp Overheating”
pdmAlertSeverity = Critical (3)
The rest Object will respond default.
Information in this document is subject to change without notice.
© 2012 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or
their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
September 2012 Rev. A00

Dell S320 Specifications

General

Number of colors	1.073 billion colors
Native aspect ratio	4:3
Projection distance	0.4 - 3.82 m
Projection technology	DLP
Supported aspect ratios	16:9
Contrast ratio (typical)	2200:1
Screen size compatibility	31.45 - 300 \
Projector native resolution	XGA (1024x768)
Keystone correction, vertical	-40 - 37 °
Offset	115 %
Throw ratio	0.62:1
Zoom capability	Yes
Focal length range	- mm
Lamp power	240 W
Light source type	Lamp
Service life of light source	3000 h
Service life of light source (economic mode)	4000 h
Full HD	No
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720i
Analog signal format system	NTSC, NTSC 4.43, NTSC J, NTSC M, PAL B, PAL D, PAL G, PAL H, PAL I, PAL M, PAL N, SECAM B, SECAM D, SECAM G, SECAM K, SECAM K1
RMS rated power	5 W
Number of built-in speakers	1
HDMI version	1.4a
Composite video in	0
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
VGA (D-Sub) ports quantity	3
Noise level	35 dB
Noise level (economic mode)	31 dB
Placement	Desktop
Product type	Short throw projector
Product color	White
Market positioning	Short throw
Cable lock slot type	Kensington
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.5 W
Power consumption (typical)	305 W
Power consumption (PowerSave)	15 W
Storage temperature (T-T)	0 - 60 °C
Operating temperature (T-T)	5 - 35 °C
Storage relative humidity (H-H)	0 - 90 %
Operating relative humidity (H-H)	0 - 80 %

Weight and Dimensions

Depth	220 mm
Width	288 mm
Height	92 mm
Weight	3180 g