EasyManua.ls Logo

DeLonghi EC 860 - Page 7

DeLonghi EC 860
11 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
12
2. Placeacuporothercontainerunderthemilkspouttube.
3. Keepthe“CLEAN” button(g.25)pressed:lights
and
ash. When the lights stop ashing and the
appliancegoesbacktoreadyforuse,releasethe“CLEAN”
button: the steam cleans the circuits inside the milk
frother.
Program the amount of coee and milk in the cup for
cappuccino or milk
Themachinehasbeensetbydefaulttodeliverstandardamounts
ofcoeeandmilk.Ifyouwouldliketoamendthesequantities,
proceed as follows:
1. Placeacupunderthecoeespoutsandthemilkspout
tube.
2. Pressthebuttonrelativetothepreparationwithmilkto
beprogrammedandkeepitpressed.Afterafewseconds,
themachinestartsdeliveringthemilk.
3. Oncetherequiredquantityofmilkhasbeendeliveredinto
thecup,releasethebutton;milkdeliverystops.
4. Program the amount of coee into the cup as for the
amountofmilk.
5. Programming is conrmed by the lights ashing for 3
seconds.
The machine is now re-programmed according to the new
amountsofmilkandcoee.
Preparing the hot water and steam
Scalding hazard!
Do not leave the machine unattended when delivering hot
water.Thespoutheatsupduringdelivery,therefore,onlythe
blackpartmustbeheld.
Delivering hot water
1. Checkthehotwaterspoutiscorrectlyattached(g.8).
2. Placeacupunderthespout(asnearaspossibletoavoid
sprays).
3. Pressthe button(B7):therelativelightashesand
theappliancestartshotwaterdelivery.
4. Themachineautomaticallystopsdelivery.
Please note!
• Tomanuallyinterruptthehotwaterdelivery,press
buttonagain.
Programming the amount of water automatically
delivered
Ifyouwouldliketoamendtheamountofwatersetbydefault,
proceed as follows:
1. Placeacupunderthewaterspout.
2. Keepthe buttonpressed.
3. Whenthehotwaterinthecupreachestherequiredlevel,
release the button. Programming is conrmed by the
lightsashingforthreeseconds.
The machine is now re-programmed according to the new
amount.
Delivering steam
1. Checkthehotwaterspoutiscorrectlyattached(g.8).
2. Fillacontainerwiththeliquidtobeheated/frothedand
immersethewater/steamspoutintotheliquid.
3. Presstwicethe button(B7):therelativelightashes
andtheappliancestartssteamdelivery.
4. When the required temperature is obtained, interrupt
steamdeliverybypressingthebuttonagain.(Youshould
notdischargesteamformorethan3minutesatatime).
Important!
Always stop steam delivery before extracting the container
containingtheliquidtoavoidburnsfromsplashes.
Cleaning the water spout after use
Alwayscleanthespoutafterusetoavoidthebuild-upofmilk
residuesandpreventthespoutfromclogging.
1. Placeacontainerunderthecappuccinomakerandpress
the buttontodeliveralittlewater(g.3).
Stop the ow of water by pressing the button
again.
2. Wait a few minutes for the cappuccino maker to cool
down,thenextractthehotwaterspout.
3. Checktheholeisnotblocked.Ifnecessary,cleanwitha
pin.
4. Washallpartsofthecappuccinomakerthoroughlywitha
spongeandwarmwater.
5. Reinsertthewaterspout.
Cleaning
Attention!
• Do not use solvents, abrasive detergents or alcohol to
cleanthemachine.
• Only the milk container (D)can be washed inthe dish
washer.Nootherpartoftheappliancecanbewashedin
thedishwasher.
•
Do not use metal objects to remove coee deposits or
foulingastheymightscratchthemetalorplasticsurfaces.
en
Instructions for use

Related product manuals