DeLonghi ECAM22.360 User Manual

17
The lter lasts about two months if the appliance is used nor-
mally. If the coee machine is left unused with the lter in-
stalled, it will last a maximum of three weeks.
3. To activate the lter, run tap water through the hole in the
lter as shown in the gure until water comes out of the
openings at the side for more than a minute (g. 30).
4. Extract the tank from the appliance and ll with water.
5. Insert the lter in the water tank and immerse it com-
pletely for about ten seconds, sloping it to enable the air
bubbles to escape (g. 31).
6. Insert the lter in the lter housing (g. 32A) and press as
far as it will go.
7. Close the tank with the lid (g. 32B), then replace the tank
in the machine.
When you install the lter you must notify the appliance of its
presence.
8. Press the MENU button to enter the menu;
9. Press the or button repeatedly until “Install l-
ter” is displayed.
10. Press the button.
11. “Enable?” is displayed.
12. Press the button to conrm the selection. “HOT WA-
TER Conrm?” is displayed.
13. Position a container with a minimum capacity of 100 ml
under the spout.
14. Press the button to conrm the selection. The
appliance begins hot water delivery and the message
“Please wait” is displayed.
15. After delivery, the appliance returns automatically to the
“Ready for coee” position.
The new lter is active and indicated by an asterisk displayed
under “Install lter” in the menu. You can now use the appli-
ance.
Replacing the lter
When “REPLACE FILTER” is displayed, after two months (see
date indicator) or when the appliance has not been used for 3
weeks, you should replace the lter:
1. Extract the tank and exhausted lter;
2. Take the new lter out of its packet and proceed as illus-
trated in points 3, 4, 5 and 6 in the previous section.
3. Position a container with a minimum capacity of 100 ml
under the spout.
4. Press the MENU button to enter the menu;
5. Press the or button repeatedly until “Replace
lter” is displayed.
10. Press the button;
11. The message “Conrm?” is now displayed;
12. Press the button to conrm the selection;
13. “HOT WATER Conrm” is displayed;
14. Press the button to conrm the selection. The
appliance begins hot water delivery and the message
“Please wait” is displayed.
15. After delivery, the appliance returns automatically to the
“Ready for coee” position.
The new lter is now active and you can use the coee ma-
chine.
Removing the lter
If you want to use the appliance without the lter, you must
remove it and notify the appliance of its removal. Proceed as
follows:
1. Extract the tank and exhausted lter;
2. Press the MENU button to enter the menu;
3. Press the or button repeatedly until “Remove
lter*” is displayed;
4. Press the button;
5. The message “Conrm?” is now displayed;
6. Press the button to conrm and the MENU button
to exit the menu.
TECHNICAL DATA
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1450W
Pressure: 15 bars
Water tank capacity: 1.8 litres max.
Size LxHxD: 238x345x430 mm
Cable length: 1,15 m
Weight: 9,1Kg
Coee beans container capacity: 250 g max
The appliance complies with the following EU directives:
• Low Voltage Directive 2006/95/EC and subsequent
amendments;
• EMC Directive 2004/108/EC and subsequent amend-
ments
• ECRegulation1275/2008forstandby
• Materialsandaccessoriescomingintocontactwithfood
conform to EEC regulation 1935/2004.
DISPOSAL
In compliance with European directive 2002/96/EC,
the appliance must not be disposed of with house-
hold waste, but taken to an authorised waste sepa-
ration and recycling centre.

DeLonghi ECAM22.360 Specifications

General

Brand	DeLonghi
Model	ECAM22.360
Category	Coffee Maker
Language	English