DeLonghi TCH8093ER User Manual

5
Heating 2
Heating 3
5.1 Fan
In this mode, only the fan operates and the
appliance does not heat the room.
5.2 Freeze prevention
In this mode, the appliance keeps the room at a
temperature of 7°C to avoid freezing.
5.3 Heating 1, 2 and Heating 3
In this mode, the desired temperature can be
selected by pressing the adjustment buttons +
and – ( B ). By pushing the + or - button once,
the temperature (shown on the display) will
increase or decrease by 1°C.
Heating 1
The appliance operates at low power, reducing
noise levels and energy consumption to a
minimum.
Heating 2
The appliance operates at medium power.
Heating 3
The appliance operates at high power to heat
the room rapidly. The setting temperature range
available is from 16°C to 32°C.
6. “ECO plus” function
The “ECO plus” function is available in Heating 1, 2 and 3
modes only. To activate the function, press the “ECO plus”
button (D).
When this function is active the appliance automatically
sets the most appropriate power level to guarantee
optimum comfort while reducing energy consumption.
While the “ECO plus” function is active, the appliance may
switch automatically to a lower heating power than the
one displayed. This may happen a number of times in an
hour.
7. To distribute the air ow over a wider surface, press
the swing button (F) . The appliance starts
swinging to the right and left. To stop the appliance
in the desired position, simply press the swing button
(F) again.
8. To turn the appliance o, press the ON/STAND-BY
button (A). The display may visualize a countdown
for about 6 seconds.
Please note: Room temperature can be displayed in
either °C or °F. To change the unit of measurement for the
temperature, press the + button for a few seconds, then
release.
Digital 24 h timer
This function can be activated from any operating mode.
Auto-start: with the appliance in STAND-BY, press
the timer button (E) . The symbol is displayed
together with the time remaining before the appliance
comes on. To adjust the timer, use the adjustment buttons
+ and - (B), then wait a few seconds for the setting to be
memorised. The stand-by light (H) is displayed together
with the symbol, indicating that the timer has been
set. When the programmed time is reached, the appliance
comes on with the settings used during the previous
period of operation.
Auto-o: with the appliance on, press the timer button
(E). The symbol is displayed together with the
time remaining before the appliance goes o. To set the
timer, use the adjustment buttons + and - (B), then
wait a few seconds for the setting to be memorised. The
current settings are displayed again, together with the
symbol indicating that the timer has been set. When
the programmed time is reached, the appliance goes o
automatically. To go back to operation without the timer,
press the timer button (E) twice.
The timer symbol disappears from the display.
Using the remote control
The functions on the remote control are the same as
those on the appliance control panel. For a description of
the functions, see the “Operation and use” section on the
previous page.
Inserting or replacing the batteries
The remote control is powered
by a CR2032 lithium battery.
To operate the remote
control, pull and remove
the plastic strip under the
battery cover. To replace the
batteries, remove the battery
cover by sliding it as shown
in the gure. When replacing
the batteries, make sure you
respect the polarity (see
gure 2).
Fig. 2

DeLonghi TCH8093ER Specifications

General

Type	-
Heating power	2400 W
Heating power (min)	800 W
Adjustable thermostat	Yes
Suitable for room volume up to	70 m³
Product color	Black, White
Placement options	Floor
Heat source	Electric
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz

Weight and Dimensions

Depth	269 mm
Width	275 mm
Height	695 mm