3
HI
POWER SWITCH
MODE SWITCH
JUNCTION BOX
SWITCH BOX
WHITE
BLACK
OFF
ON
WHITE
BLUE
GREEN
GRD
L
N
L
N
ON/OFF SWITCH
(purchase separately)
SWITCH BOX
120 VAC
LINE IN
WIRING
PLATE
BLACK
WHITE
GROUND
(bare)
BLUE
MODE
SWITCH
POWER
SWITCH
JUNCTION BOX
SWITCH BOX
WHITE
BLACK
OFF
ON
RED
GRD
L
N
N
GREEN
WHITE
SWITCH
Dual Speed Model: 150DS
ON/OFF SWITCH
(purchase separately)
SWITCH BOX
120 VAC
LINE IN
WIRING
PLATE
BLACK
WHITE
GROUND
(bare)
RED
LIGHT
SWITCH
POWER
SWITCH
OTHER WIRING OPTION
LED Adjustable Model: 150LED-ADJ
Combine power & light to one switch.
Turn the switch on, fan runs and the light on at the
same time.
ON/OFF SWITCH
(purchase separately)
SWITCH BOX
120 VAC
LINE IN
WIRING
PLATE
BLACK
WHITE
GROUND
(bare)
RED
1. With the power on, check for abnormal vibrations
or sounds.
Insert mounting springs into the slots and mount
the grille to the fan body.
2.
For 150F/150DS
GRILLE INSTALLATION
Slots
Spring
Slots
Spring
LED light
connector
Grille
Celling
1. Insert the LED light connector into the LED
socket.
With the power on, check for abnormal vibrations
or sounds.
Insert mounting springs into the slots and mount
the grille to the fan body.
2.
For 150LEDNL
3.
Grille
Light Connector
Spring
Slots
CCT Switch
1. Insert the LED light connector into the LED
socket.
Using the switch on the back of grille, choose the
color temperature you want for your LED.
You can choose from 2700K warm white, 4000K
cool white, and 5000K daylight white.
With the power on, check for abnormal vibrations
or sounds.
Insert mounting springs into the slots and mount
the grille to the fan body.
2.
For 150LED-ADJ
3.
4.
Using the switch on the back of grille, choose the
color temperature you want for your LED.
You can choose from 2700K warm white, 4000K
cool white, and 5000K daylight white.
150DS
Delay time control
(150DS)
Low speed
air volume
preset control.
control options
Turn the switchs on/off to operate the fan / light / night
light.
Dual Speed Model: 150DS
1.
OPERATION
Low speed control mode: Turn the POWER switch
on (MODE switch is off) to operate at the user-
adjustable low speed air flow - the LED indicator
will be green.
Full speed control mode: Turn the POWER switch
& MODE switch on to operate at full speed mode
- the LED indicator will be amber. When the user
turns the MODE switch off, the fan will continue
to run at the full speed until the user-adjustable
time delay has elapsed, and then will automatically
change to the user-adjustable low speed air flow -
the LED indicator will be green.
2.
Factory setting: Low speed airflow 70CFM, time delay
15 minutes.
CARE AND MAINTENANCE
TURN OFF POWER SOURCE. REVIEW ALL
SAFETY PRECAUTION.
1. To remove grille, unplug the LED light connector
(For 150LEDNL and 150LED-ADJ), squeeze
springs and pull down.
Wash and clean grille with non-abrasive kitchen
detergent. Then wipe dry with a new cloth.
Caution: Do not let water into the LED light engine.
Remove dust and dirt from the fan body with a
vacuum cleaner.
Using a cloth dampened with non-abrasive kitchen
detergent, remove dust and dirt from the fan body.
Then wipe dry with new cloth.
Replace the grille back onto the fan body. Plug
the light and fan power into the junction box of
housing. Turn the switchs on/off to operate the fan/
light/night light again.
See safety information before proceeding.
Routine maintenance must be done every year.
CAUTION
• Never use gasoline, benzene, thinner or any other
such chemicals to clean the ventilating fan.
• Do not allow water to enter the motor.
• Do not soak resin parts in water over 140°F (60°C).
CLEANING
2.
3.
4.
OFF
To Next Page
Loading...
Need help?
General