To Next PageTo Next Page
Need help?Do you have a question about the Delta VFD015EL21W-1 and is the answer not in the manual?
General| Control Method | V/F control |
|---|---|
| Protection Level | IP20 |
| Input Voltage | 200 ~ 240 VAC |
| Input Phase | 1-Phase |
| Frequency Range | 0.1 Hz |
Procedures for inspecting the AC motor drive upon receipt, checking for damage and verifying the part number.
Guidelines for preparing the AC motor drive and the installation environment before wiring and setup.
Technical drawings and specifications for the physical dimensions of different drive frames.
Visual identification of different drive frames (A1, A2, B) and their key components.
Guidance on locating and managing the RFI jumper for grounding and EMC compliance.
General wiring instructions and diagrams for main circuits and control circuits of the AC motor drive.
Detailed explanation of external wiring components like fuses, reactors, and EMI filters.
Information on connecting the main power terminals (R/L1, S/L2, T/L3) and output terminals (U, V, W).
Specifications for main circuit terminals including wire gauge and screw tightening torque for different frames.
Explanation of terminal symbols and functions for digital, analog, and communication signals.
Configuration options for NPN and PNP input modes for digital control signals.
Overview of the digital keypad layout, including LEDs, display, and navigation keys.
Explanation of various display messages and codes shown on the digital keypad.
Step-by-step guide for operating the keypad, including parameter setting and mode selection.
How to select and configure the drive's operation method (keypad, communication, external signals).
Procedures and checks for performing a trial run of the AC motor drive and motor.
Overview of the 11 parameter groups and their general purpose for easy configuration.
Application-specific parameter settings for optimizing drive performance in various scenarios.
Parameters related to drive identity, reset, and display configuration for user settings.
Fundamental parameters for motor operation, including frequency, voltage, and acceleration/deceleration times.
Settings for selecting frequency command sources and operation command sources.
Configuration of multi-function output relays and fan control for various operational signals.
Settings for multi-function input terminals, including potentiometer and analog inputs.
Parameters for setting multiple distinct speed levels for stepped operation.
Parameters for various protective functions like over-voltage, over-current, and overload.
Settings related to motor characteristics, auto-tuning, and thermal protection.
Parameters for advanced functions like DC brake, skip frequency, and auto-energy saving.
Settings for RS-485 communication, including address, speed, and protocol.
Parameters for configuring the PID control loop for precise process regulation.
Troubleshooting guide for over-current faults, including causes and corrective actions.
Troubleshooting guide for over-voltage faults, addressing causes like regeneration and deceleration time.
Troubleshooting guide for low voltage faults, checking input power and system stability.
Troubleshooting guide for overheat faults, focusing on heat sink temperature and cooling fan issues.
Troubleshooting guide for overload faults, suggesting load reduction or setting adjustments.
Comprehensive guide for diagnosing and resolving issues when the motor fails to start or run.
Solutions for mitigating electromagnetic and induction noise affecting drive performance.
List of fault codes, their descriptions, and corresponding corrective actions for diagnosis.
Schedule and procedures for routine visual and functional checks of the AC motor drive.
How to reset the drive after a fault has been cleared and ensure safe operation.
Electrical and mechanical specifications for the 230V, single-phase series of drives.
Electrical and mechanical specifications for the 460V, three-phase series of drives.
Comprehensive overview of the drive's control, operating, and protection characteristics.
Environmental conditions and certifications for operating, storing, and transporting the AC motor drive.
Curves illustrating how ambient temperature and carrier frequency affect rated current.
Recommended non-fuse circuit breaker ratings and fuse specifications for drive models.
Detailed description of the VFD-PU06 digital keypad, its functions, display messages, and operation flow.
Specifications and features of the VFD-PU08 and VFD-PU08V digital keypads.
Information on installing an optional cooling fan to extend operating temperature limits.
Mathematical formulas and calculations for determining the required AC motor drive capacity.
Important safety and operational precautions when selecting and installing an AC motor drive.
Guidelines and considerations for selecting the most appropriate motor for use with the AC motor drive.
