Denon AVC-2800 - Surround Modes and Parameters; Microprocessor Initialization

ENGLISH 2
e Using the surround function
1. Select the surround mode according to
the input source. .
SUPER
STADIUM
ope
2.|f necessary, adjust the levels.
: ; 6
3.Adjust the parameters to the desired
settings.
4.To check the DSP effect, press the
EFFECT button to turn the effect on and
off.
Ic
EFFECT = y,
5.To set the parameters back to the stan-
dard settings, press the CLEAR button.
CLEAR}
CLEAR Q) y,
e Surround modes and parameters
DELAY
TIME
oo...
cece
This
can
be
set
to
between
15
and
30
msec
for
the
DOLBY
PRO
LOGIC
mode,
between
0
and
360
msec
for
the
MATRIX
mode.
It
is
controlled
directly
with
the
DSP
EFFECT
“+”
and
“—
buttons.
These parameters can be used in modes other than the DOLBY PRO LOGIC and MATRIX modes.
ROOM SIZE “Room size” refers to the size of the sound field.
EFFECT
LEVEL
“Effect
level”
refers
to
the
strength
of
the
effect
sounds.
If
the
sound
is
distorted
or
seems
strange,
lower
the level.
BEFECR
siccctcssscssscespstenteadses
This
can
be
used
in
surround
modes
other
than
DOLBY
PRO
LOGIC,
WIDE
SCREEN,
LIVE
SURROUND
and
MATRIX
MODE.
CENTER
LEVEL
on...
eeeseeeeee
This
can
be
used
in
the
DOLBY
PRO
LOGIC,
WIDE
SCREEN,
and
LIVE
SURROUND
modes
when
the center mode is set to the normal or wide mode. In other cases, the center output is
automatically turned off.
When this is selected in the DOLBY PRO LOGIC mode, the wide screen and live mode center
modes are automatically set.
CENTER MODE ...
e Using the Personal Memory function
The personal memory function allows you to store the
current input position and surround mode in memory.
Both settings can then be recalled instantly by pressing a
single button.
Presetting ® ooocooa & ©
1.Set the desired input position and sur-
round mode using the procedures de-
scribed in sections 4-2 and 4-8.
2. Press the Personal memory “MEMORY”
button, The standby mode is set.
Oxy
3.Press the button (1 to 3) at which you
want to store the setting.
RY
The setting is now stored.
Recalling
4. Press the button (1, 2 or 3) at which the
desired setting has been stored.
The unit automatically switches to that
setting.
——PERSONAL MEMORY—
OO0 |es
%
The DAT/TAPE MONITOR position can-
hot be stored in the memory.
10
[5] EASY OPERATION FUNCTIONS
This
unit
is
equipped
with
the
functions
described
below
to
make
operation
simpler.
5-1 On-screen display
Each
time
an
operation
is
performed,
a
description
of
that
operation
appears
on
the
display
connected
to
the
unit’s
VIDEO
MONITOR
OUT
terminal.
Also,
the
unit's
operating
status
can
be
checked
during
playback
by
pressing
the
remote
control
unit's
ON
SCREEN
button.
:
Such
information
as
the
position
of
the
input
selector
and
the
surround
parameter
settings
is
output
in
sequence.
The
output
from
the
S
MONITOR
OUT
terminal
has
priority
for
the
on-screen
display.
If
you
want
to
always
output
the
on-screen
display
signals
to
the
video
output,
do
not
connect
a
cable
to
the
S
MONITOR
OUT
terminal.
The
on-screen
display
is
not
displayed
for
the
MULTI
SOURCE
MONITOR
OUT
terminal.
This
model's
on-screen
function
is
designed
for
high
resolution
monitor
displays.
Small
characters
may
be
difficult
to
read
on
small
displays
or
low
resolution
TVs.
“ON SCREEN”
5-2 Front panel display
Descriptions
of
the
unit's
operations
are
also
displayed
on
the
front
panel
display.
In
addition,
the
display
can
be
switched
to
check
the
unit’s
operating
status
while
playing
a
source
by
pressing
the
remote
control
unit's
PANEL
button.
“PANEL”
5-3 Personal memory
This
is
a
function
allowing
you
to
easily
set
the
input
position
and
surround
mode
with
a
single
button
once
the
input
selector
and
surround
mode
have
been
preset.
For
details,
refer
to
Page
10.
5-4 System call (Remote contro! unit)
This
function
allows
you
to
preset
frequently
used
operation
patterns
in
the
remote
control
unit
then
automatically
send
a
series
of
up
to
ten
remote
control
codes
with
a
single
button.
Presetting
1.Press the SET button,
[Bey
2. Press the buttons for the codes to be sent,
changing the position of the slide switch
as necessary. (Up to ten buttons can be
set.)
Buttons which have been “learned” and
buttons which have been preset can also
be selected.
3.Press the SYSTEM CALL button ("1" or
“2") at which you want to store the codes,
The setting is now stored.
@
‘STEM CAI
Recalling
4.Press the SYSTEM CALL button ("1" or
“2") at which the desired codes have been
stored.
The series of codes is now sent.
SYSTEM CALL
XY
[6]
INITIALIZATION
OF
THE
MICROPROCESSOR
When
the
indication
of
the
display
is
not
normal
or
when
the
operation
of
the
unit
does
not
shows
the
reasonable
result,
the
initialization
of
the
microprocessor
is
required
by
the
fotlowing
procedure.
1. Switch off the unit and remove the AC power cord from the
wall outlet.
2.Hold
the
following
AUDIO
FUNCTION
button
and
VIDEO
FUNCTION
button,
and
plug
the
power
cord
into
the
outlet.
3. Check that the entire display is flashing with an interval of
about 1 second, and release your fingers from the 2 buttons.
4.
Switch
on
the
unit
and
the
microprocessor
will
be
initialized.