Denon AVC-2800 - Remote Control Unit; System Code Buttons; Preset Memory Setup

ENGLISH :
[3] REMOTE CONTROL UNIT
Following the procedure outlined below, insert the batteries before using the remote controf unit.
MRange of operation of the remote control unit
Approx. 7m/20 feet
inserting the batteries
1. Open the bottom cover of the remote control unit and
remove the battery cover.
2. Insert the two R6P/AA batteries, matching the ® and
© marks on the batteries with those in the case.
Close the bottom cover until it clicks shut.
3-1 System code buttons
DENON remote-controllable audio components can be controlled using this unit’s remote control
unit. Note that some components, however, cannot be operated with this remote control unit.
1.Set to slide switch to “AUDIO” (“AVR/
AVC").
DAT}.
AUDI
AVR/AVC VIDEO
2. Set the slide switch to the position for the
component to be operated (CD, DECK or
Point the remote contro} unit at the remote control sensor
as shown on the diagram at the left.
NOTES:
@ The remote control unit can be used from a straight
distance of approximately 7 meters/20 feet, but this
distance will shorten or operation will become difficult if
there are obstacles between the remote control unit and
the remote control sensor, if the remote control sensor is
exposed to direct sunlight or other strong light, or if
operated from an angle.
e Neon signs or other devices emitting pulse-type noise
nearby may result in malfunction, so keep the set as far
away from such devices as possible.
NOTES
e@ Use only AA, REP, UM-3 batteries for replacement.
e Be sure the polarities are correct. (See the illustration
inside the battery compartment.)
e Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
elf batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact
with clothing, etc. Clean the battery compartment thor-
oughly before installing new batteries.
e@ Have replacement batteries on hand so that the old
batteries can be replaced as quickly as possible when the
time comes.
@ The codes that have been learned may be lost if removed
batteries are not replaced within about 5 minutes.
—CD.DECK 1
—vbP vcA
3.Use the buttons shown below to operate the component.
For details, refer to the respective component's manual.
b.For tape decks
a.For CD players and DATs
XZ VOLUME 4
SSO
3-2 Preset memory
This
remote
control
unit
can
be
used
to
operate
components
of
other
manufacturers
without
using
the
learning
function
by
registering the manufacturer of the component as shown on the diagrams below.
1.Set the slide switch to “VIDEO”.
AUDI
AVRVAVC VIDEO
2.Set the slide switch to the compo-
nent to be registered (VDP, VCR or
TV).
= D_QECK DAT
—vBF vor’
Ex.: To preset a VDP in the personal
memory
4. Next, while holding in the POWER
button, press the button for the code
in block B. (Refer to Table 1.) The
operation is completed when the
LEARNED/TX LED lights.
Es c
3. Holding in the POWER button, press
the button for the corresponding
manufacturer in block A.
(Refer to Table 1.)
The LEARNED/TX LED flashes.
5.To continue registering other com-
ponents, repeat steps 2 to 4.
e Operation after components are registered
After components are registered, they can be operated using the buttons in block C shown
below. For details, refer to the respective component's manual. Before operating the
component, set slide switch @ to the position for that component.
1, VDP
Table 1: Combinations of Preset Memory System Codes for Different Manufacturers
“VDP”
“VCR”
2] button
button
——
2 (VDP/TV}
3 (PHONO)
2(vDP/TV) | HITACHI A
HITACHI B
[ HITACHI Cc
3 (PHONO)
MITSUBISHI A
MITSUBISHI B | MITSUBISHI C
4 (TUNER)
4 (TUNER)
PANASONIC A | PANASONIC B
5 (VCR-1)
5 (VCR-1)
JVC (VICTOR) A} JVC (VICTOR) B
SONY C |
OOO ©
6 (VCR-2) 6 (VCR-2} SON® A SONY B
PIONEER - —
TOSHIBA A TOSHIBA B =
9 (MULTI) SANYO 9 (MULTI) SANYO A SANYO B -
iT at 1O0(V.AUX/GAME}| SHARP A SHARP B -
==
11/0(DAT/TAPE)
_
TVO(DAT/TAPE)|
NEC
A
NEC
B
NEC
C
PHILIPS 12/E PHILIPS A PHILIPS B PHILIPS C
STEREO RCA STEREO RCA A RCA B -
MODE _—
TONE/DIRECT | MAGNAVOX
GENERAL
MODE
GENERAL
TONE/DIRECT
ELECTRIC A | ELECTRIC B
MAGNAVOX A | MAGNAVOX B
Tene