Denon AVC-2800 - Learning Function Operation; Clearing Preset Memory

“Tv" 3-3 Remote Control Unit Learning Function
[2]
button
[2]
button
Use
the
learning
function
to
operate
audio
components
manufactured
by
companies
other
than
DENON
and
when
your
VCR
4
or TV
does
not
operate with
the preset
memory function.
DENON
HITACHI A HITACHI B ar
3 {PHONO} MITSUBISHI A | MITSUBISHI 8 | MITSUBISHI C
A(TUNER) PANASONIC
5 (VCR-1) JVC (VICTOR)
6 (VCR-2) SONY
7 PIONEER ~_
8 (CD) TOSHIBA
9 (MULTI SANYO A SANYO B
10{V.AUX/GAME)| SHARP _
cr A NEC B
+. Press the USE/LEARN selector but-
ton with the tip of a pen etc., to set
the learn mode. Both the START and
LEARNED/TX indicators flash.
2(VDP/TV) 5. Check that the START LED is lit, then
press the button to be “learned” on
the other remote control unit.
Flashes
4
Ss
Sy
NEC C
PHILIPS C
This unit's remote control unit
6. Once the START LED turns off and
2.Set the program switch to the side the LEARNED/TX LED lights, re-
to be “learned”. lease the button on the other remote
Set to the AUDIO side for the CD, control unit.
tape deck or DAT position, to the
VIDEO side for the CDP, VCR or TV
V2/E PHILIPS A PHILIPS B
STEREO RCA A RCA B
GENERAL GENERAL
MODE ELECTRIC A | ELECTRIC B
a NOTE:
_ Preset memory function will not work for some
models or some codes.
MAGNAVOX C In such case, please use the learning function.
TONE/DIRECT | MAGNAVOX A | MAGNAVOX B position.
¢ Clearing the Preset Memory AVRIAVG VIDEO
1.Press
the
USE/LEARN
selector
but-
4.Press
the
SYSTEM
CALL
SET
but-
3.Set
the
program
switch
to
the
posi-
ton with the tip of a pen, etc., to set ton, and hold it in for at least four
tion to be “learned”.
the learn mode. seconds.
The two LEDs start flashing again.
7.To “learn” other buttons, repeat
steps 4 and 5.
4. Set the remote control units so they
are facing each other, then press the
button to be “learned” on this unit's
remote control unit.
8. Once the learning operation is com-
pleted, press the USE/LEARN selec-
tor button again.
The two LEDs stop flashing and the
learning mode is cancelled.
9.For instructions on resetting
the “learned” codes, refer to
“clearing the Preset Memory”.
Transmitting windows
5.When both the START and
LEARNED/TX LEDs light simul-
taneously, all the stored codes are
cleared.
2. Set the slide switch to “VIDEO”.
Other remote
control unit
Lit
8 Approx.
AVRIAVE VIDEO— # This unit's remote acm
rte control unit
ARQ
3.
Set
the
program
switch
to
the
sid
om
indi
i
prog ‘o the side 14 The indicator stops flashing and the
to be cleared. ra START LED lights. Check that the stored codes work
The learnable buttons are the but- properly.
tons which can be operated with the
DENON system codes for the CD
player, DAT and tape deck, the but-
tons which can be operated with the
preset memory for the VCR, VDP
and TV. For the TV only, however,
the buttons in the section indicated
“A” on the diagram above can also
be “learned”. Use these to “learn”
TV channels.
— GQDECK DAT
NOTES:
e Up to 26 codes can be “learned”, but this number may be lower if the
codes are long.
e If a non-learnable button is pressed or two or more buttons are pressed at
once, the two LEDs will once again light when the button(s) is released.
¢ If the codes could not be stored, the LEARNED/TX LED does not tight after
the eis LED turns off. (This may happen for a limited number of
models.
® If the two LEDs start flashing rapidly after the START LED lights, this means
that the memory is already full, and the code you have just attempted to
store was not stored.
To “learn” that code, first perform the resetting operation.
—vbP VCR WV
Ex.: To clear the VDP preset
memory