EasyManuals Logo

Denon AVR-X540BT User Manual

Denon AVR-X540BT
138 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #107 background imageLoading...
Page #107 background image
o
Desired sound does not come out
Symptom Cause / Solution Page
The volume does not
increase.
0
The maximum volume is set too low. Set the maximum volume using “Limit” on the menu. 78
0
Appropriate volume correction processing is performed according to the input audio format and settings,
so the volume may not reach the upper limit.
No sound comes out with
the HDMI connection.
0
Check the connection of the HDMI connectors. 26
0
When outputting HDMI audio from the speakers, set “HDMI Audio Out” on the menu to “AVR”. To output
from the TV, set “TV”.
80
No sound comes out of a
specific speaker.
0
Check that speaker cables are properly connected. 22
0
Check that a selection other than “None” is set for the “Speaker Config.” setting in menu. 91
0
When the sound mode is “Stereo” and “Virtual”, audio is only output from the front speakers and
subwoofer.
No sound is produced from
subwoofer.
0
Check the subwoofer connections. 23
0
Turn on the subwoofer’s power.
0
Set “Speaker Config.” - “Subwoofer” on the menu to “Yes”. 91
0
When “Speaker Config.” - “Front” in the menu is set to “Large”, depending on the input signal and the
sound mode, no sound may be output from the subwoofer.
91
0
When no subwoofer audio signal (LFE) is included in the input signals, no sound may be output from the
subwoofer.
94
0
You can make the subwoofer always output sound by setting the “Subwoofer Mode” to “LFE+Main”. 94
DTS sound is not output.
0
Check that the digital audio output setting on the connected device is set to “DTS”.
0
Set “Decode Mode” on the menu to “Auto” or “DTS”. 85
Dolby TrueHD, DTS-HD,
Dolby Digital Plus audio is
not output.
0
Make HDMI connections. 30
0
Check the digital audio output setting on the connected device. On some devices, “PCM” is set by default.
Dolby PLg mode or DTS
Neo:6 mode cannot be
selected.
0
It cannot be selected when “None” is set for “Speaker Config.” - “Center” and “Surround”. 92
0
Dolby PLg or DTS Neo:6 cannot be selected when using headphones.
Contents Connections Playback Settings Tips Appendix
107
Front panel Display Rear panel Remote Index

Other manuals for Denon AVR-X540BT

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X540BT and is the answer not in the manual?

Denon AVR-X540BT Specifications

General IconGeneral
Channels5.2
HDMI Inputs5
HDMI Outputs1
BluetoothYes
4K Ultra HD Pass-throughYes
Dolby TrueHDYes
DTS-HD Master AudioYes
Auto Speaker CalibrationNo
Number of Power Amps5
Output Power (6 ohm, 1 kHz, 0.7% 2ch Drive)90 W
Output Power (6 ohm, 1 kHz, 10% 1ch Drive)140 W
Composite In2
Composite Out1
Digital In: Optical2
Analog In2
Speaker Terminal: ScrewYes
FM Tuner with RDSYes
3D Signal Pass-ThroughYes
Audio Return ChannelYes
HDMI Standby Pass-ThroughYes
CECYes
Auto Speaker Setup by MicrophoneNo
Dimensions (W x H x D)434 x 151 x 319 mm
Weight7.5 kg
Total Harmonic Distortion0.08 %
Input Sensitivity/Impedance200 mV / 47 kΩ
Signal-to-Noise Ratio98 dB
Ethernet PortNo
Wi-FiNo
Power Output per Channel70W (8 ohms, 20Hz - 20kHz, 0.08% THD)
Frequency Response10Hz - 100kHz
Supported Audio FormatsMP3, WMA, AAC

Related product manuals