Denon AVR-X8500H - Page 320

Multi Ch Stereo
SDDDz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 D z12z13 D z12z13 Dz12 Dz12 Dz12 D
Rock Arena
SDDDz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 D z12z13 D z12z13 Dz12 Dz12 Dz12 D
Jazz Club
SDDDz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 D z12z13 D z12z13 Dz12 Dz12 Dz12 D
Mono Movie
SDDDz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 D z12z13 D z12z13 Dz12 Dz12 Dz12 D
Video Game
SDDDz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 D z12z13 D z12z13 Dz12 Dz12 Dz12 D
Matrix
SDDDz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 Dz12 D z12z13 D z12z13 Dz12 Dz12 Dz12 D
Virtual
S D
Subwoofer
Back
Dolby
Atmos
Enabled
L/R
Surround
Dolby
Atmos
Enabled
L/R
Front
Dolby
Atmos
Enabled
L/R
Top
Surround
Center
Height
Surround
Height
L/R
Rear
Height
L/R
Top
Rear
L/R
Top
Middle
L/R
Top
Front
L/R
Front
Height
L/R
Front
Wide
L/R
Surround
Back
L/R
Surround
L/R
Center
Front
L/R
Channel output
Sound mode
z1
The applicable sound mode includes “Dolby Surround” and sound modes that have “+Dolby Surround” in the sound mode name.
z2
Audio can be played through a maximum of 11-channels when 11 speakers or more (excluding the subwoofer) are installed.
z3
The applicable sound mode includes “DTS Neural:X” and sound modes that have “+Neural:X” in the sound mode name.
z4
The applicable sound mode includes “DTS Virtual:X” and sound modes that have “+Virtual:X” in the sound mode name.
z5
A signal for each channel contained in an input signal is output as audio.
z6 Audio is output when “Subwoofer Mode” in the menu is set to “LFE+Main”. (v
p. 243)
z7 Audio is not output when “Speaker Config.” - “Surr. Back” in the menu is set to “1 spkr”. (v
p. 235)
z8
For the best Auro-3D experience Surround Height speakers are recommended, however you may substitute Rear Height speakers from a Dolby Atmos speaker setup in
place of Surround Height speakers.
z9
This is output if an Auro-3D.
z10
This is output if an Auro-3D signal is input and the input signal contains Top Surround.
z11
For the best Auro-3D experience Front Height and Surround Height speakers are recommended, however you may substitute Dolby Atmos Enabled speakers.
z12 Audio is output from the speakers specified in the “Surround Parameter” – “Speaker Select” settings. (v
p. 185)
z13
Audio is not output when connecting to the HEIGHT4/FRONT WIDE speaker terminal to use the Center Height or Top Surround speaker.
Contents Connections Playback Settings Tips Appendix
320
Front panel Display Rear panel Remote Index