To Next PageTo Next PageWhy is there no sound or distorted sound from my Denon CD Player?
If you're not getting any sound or the sound is distorted from your Denon CD Player, there could be a couple of things to check: * Make sure the output cables are properly connected to the amplifier. Check the connections to ensure they are secure. * Verify that the amplifier's function settings and controls are correctly adjusted.
How to fix a Denon DCD-520AE when the disc tray does not open?
If the disc tray on your Denon CD Player doesn't open, make sure the power is turned on.
Why does my Denon DCD-520AE CD Player display “TRACK 0 0m00s” when a disc is loaded?
If your Denon CD Player displays “TRACK 0 0m00s” even though a disc is loaded, it's likely that the loaded disc is not a CD. Try loading a CD.
What to do if MP3 or WMA files won't play on my Denon CD Player?
If files recorded in MP3 or WMA formats cannot be played, you may have selected a copyright-protected WMA file or a file that cannot be played normally. Use the o p button on the remote control unit to select a different file.
What to do if my Denon DCD-520AE CD Player doesn't respond to the remote control?
If your Denon CD Player isn't responding to the remote, here are a couple of things you can check: * First, make sure the batteries in the remote aren't dead. If they are, replace them with new ones. * Also, make sure you're not too far from the unit. Try moving closer to the CD player with the remote.
What to do if playback doesn't start on my Denon DCD-520AE CD Player?
If playback doesn't start when you press the play button on your Denon CD Player, the disc might be dirty or scratched. Try wiping the dirt off the disc or replacing it.
What to do if my Denon CD Player says “NO DISC” when a disc is inside?
If your Denon CD Player displays “NO DISC” even when a disc is loaded, it might not be properly loaded. Try reloading the disc.
Why does a specific section of a disc not play properly on my Denon CD Player?
If a specific section of a disc doesn't play properly on your Denon CD Player, the disc is likely dirty or scratched. Try wiping the dirt off or replacing the disc.
Why can't my Denon DCD-520AE play a CD-R or CD-RW disc?
If your Denon CD Player can't play a CD-R or CD-RW disc, it could be due to a couple of reasons: * The disc might not have been finalized. Finalize the disc and then try playing it again. * The recording conditions or the quality of the disc itself might be poor. Use a properly recorded disc.
General| Audio formats supported | MP3, WMA |
|---|---|
| Signal-to-Noise Ratio (SNR) | 105 dB |
| Total Harmonic Distortion (THD) | 0.003 % |
| Built-in speaker(s) | No |
| CD-RW playback | Yes |
| Playback disc formats | CD audio |
| Device type | HiFi CD player |
| Product color | Black |
| Channel separation | 100 dB |
| Headphone outputs | 1 |
| Headphone connectivity | 6.3 mm |
| Display type | VFD |
| Power requirements | AC 230 V, 50 Hz |
| Power consumption (typical) | 13 W |
Weight and Dimensions| Depth | 279 mm |
|---|---|
| Width | 434 mm |
| Height | 107 mm |
| Weight | 4000 g |
Explains the functionalities and features available within the service manual for user interaction and information retrieval.
Details the procedure for checking leakage current to ensure electrical safety before returning the unit to the customer.
Highlights critical safety parts and the importance of using designated replacement parts for user safety.
Outlines the initialization procedure for the CD player, necessary after replacing specific components like the μcom or CD PCB.
Describes the use of a specific service jig (RS232C adapter) for firmware updates.
Specific instruction on protecting the Laser Diode (LD) circuit during soldering and handling.
Safety guidelines for handling the laser pick-up mechanism to prevent damage from dust or shock.
Precautions to be taken during the assembly and adjustment process of the mechanism.
Method to test and diagnose a potentially defective laser pick-up by measuring waveforms.
Details the procedure for disassembling the main assembly of the CD player.
Explains the steps for removing and disassembling the front panel assembly.
Details the button combinations required to activate different special modes on the unit.
Describes how to display the firmware versions of the system and USB microcomputers.
Explains the mode that flashes all displays on the FL tube every 2 seconds for testing.
Details the procedure for performing a cold start initialization of the CD player.
Explains the test mode for the CD mechanism, including disc loading and servo checks.
Describes the procedure for running the CD player continuously to test its heat and operational stability.
Step-by-step guide for updating the firmware of the main MCU (IC11) using a PC.
Detailed instructions for updating the firmware of the USB μcom (IC41) via a PC.
A flowchart to diagnose power-related issues and basic voltage checks.
A flowchart for troubleshooting issues related to D+3.3V output and USB voltage supply.
Identifies specific points for measurement and displays expected waveforms for diagnostic analysis.
Presents a high-level overview of the unit's internal functional blocks and their interconnections.
Shows the component layout and routing on the different printed circuit boards.
A diagram showing the exploded view of the DCD720AE model's components.
A list of parts corresponding to the exploded view of the DCD720AE.
Details pin configurations and functions for integrated circuits (ICs) used in the main MCU.
