Denon DN-951FA - Page 5

{d2-1
|d2-2
1d2-4'
(d2-5]
[d2-6
(d2-7
{d3-1)
{d3-2]
FRAME DISPLAY — (0:
* 1}:
INITIAL DISPLAY (ol:
* Uh
END DETECT {0}:
* 1:
RE CUE * {0}:
1:
PLAY LOCK * [0]:
As
FLASH 0}:
* th:
REMOTE INHIBIT * {0):
(1):
SWITCHINHIBIT * [0]:
{1}:
Frame not displayed during playback.
Frame displayed during playback.
Elapsed time displayed when power turned on.
Remaining time displayed when power turned on.
Track ends not detected during search operation.
Track ends detected during search operation.
Stop mode set when piayback ends.
When playback ends, pickup returns to starting position and standby mode set.
Buttons other than the ones below also function during playback.
Buttons other than the PLAY MODE, TIME, PLAY/PAUSE and RESET buttons
do not function during playback.
PLAY indicator remains turned off (without flashing) during EOM operation,
PAUSE indicator remains turned off when playback ends, and STDBY/CUE
indicator remains turned off during search operstion.
PLAY indicator flashes during EOM operation, PAUSE indicator flashes when
playback ends, and STDBY/CUE indicator flashes during search operation.
“REMOTE” command accepted.
“REMOTE” command not accepted
No front panel buttons other than PLAY MODE, TIME and RESET buttons function.
All buttons function.
[d3-3, 4 and 5) E.0.M.: (PLAY/PAUSE button flashes green)
{d3-8]
[d4-1}
(d4-2}
{d4-3}
|d4-5, 6]
(d4-7]
{d3-3]
0
1
* 0
1
ty)
4
0
1
DIGITALOUT = *_—“[0}:
i
TEST * |O):
VARIABLE SPEED ENABLE
* {0}:
(i:
BAR CODE {0}:
* Th:
DELAY START:
(d4-5
* t)
1
0
1
CDR DISC * o}
i:
[d3-4] (d3-5} £.0.M. time setting
i?) 0 £.0.M. not output
0 0 5 sec
1 0 10 sec
1 0 15 sec
0 1 20 sec
0 1 25 sec
1 1 30 sec
1 1 35 sec
Standard playback mode
Only audio data output from digital output
Digital output priority mode.
Audio data and subcodes output from digital output
DSP functions (FADE IN, MONO) inhibited.
Standard playback mode. (Always leave this at [0}. The player cannot be used
if set to [1}.)
Discs played al standard speed
Discs played at speed set by variable speed presetting [d6-1, 2, 3 and 4).
Bar code plate function inhibited.
When cartridge with bar code plate inserted, standby mode set at track indicated
by bar code.
(d4-6] Delay start time setting
0 0 msec
0 100 msec
1 200 msec
1 300 msec
Mode for playing normal discs including TOCs. (Discs without TOCs cannot be played.)
Discs recorded on a CD recorder {(DN-7700R, €:c.) without TOCs can be played.
[4-8]
fd5-1!
§d5-2]
[d5-3}
[d5-4}
NEXT TRACK STANDBY
* 10):
(1h:
INDEXINHIBIT * [0]:
[}}:
INDEX 3/2 {0}:
* (1):
EOM/INDEX * [0):
(1):
FADER START MODE SELECT
{0}:
* (11:
{d5-5, 6 and 7} END MONITOR:
[d5-8]
1d5-5}
0
-o7r0+04
INDEX 2 * (0):
{1}:
When playback ends, next operation performed according to “RE CUE” setting.
When playback ends, standby mode set at next track. (“RE CUE” setting ignored.)
Index numbers can be selected.
Index numbers cannot be selected.
“INDEX 2 TALLY” output from REMOTE connector pins 24 and 25.
(Not valid when (d5-3] set to {1].)
“INDEX 3 TALLY” output from REMOTE connector pins 24 and 25.
(Not valid when {d5-3} set to [1].)
“INDEX TALLY” (set by INDEX 3/2 |d5-2}) output from REMOTE connector
pins 24 and 25.
“EOM TALLY” output from REMOTE connector pins 24 and 25.
Piayer starts when fader switch turned on.
Player starts when fader switch turned on, set io pause mode when fader
switch turned off.
[d5-6] |d5-7} End monitor time setting
0 0 End monitor off.
5 sec
10 sec
15 sec
20 sec
25 sec
30 sec
1 1 35 sec
“INDEX 3 TALLY” output from REMOTE connector pin 17.
“INDEX 2 TALLY” output from REMOTE connector pin 17
-co-+0 ~“4os000
[d6-1, 2, 3 and 4} VARHABLE SPEED: This sets the playing speed within a range of 0 to 3% when {d4-2] is set to [1].
(d6-5]
16-6]
{d6-1]
0
=e 204 05050530404
SKIP TRACK {0}:
END MARK * 10)
{1]-
{d6-2] {d6-3] |d6-4}
0 0 0
Playback speed
0.0% (Standard speed)
+0.2%
+0.4%
+0.6%
+0.8%
+1.0%
41.2%
+1.4%
+1.6%
+1,8%
+2.0%
+2.2%
+2.4%
+2.6%
+2.8%
1 1 1 +3.0%
Skip track piayback as set in the TOC is possible when playing CDR discs
Skip track playback as set in the TOC is not possible when piaying COR discs
The track end position does not change even if the PLAY/PAUSE button is pressed
Guring the end monitor mode
The position at which the PLAY/PAUSE button is pressed during the end monitor
function becomes the track end position.
eee ene ooo00000 “Ac O4~cGOo~ +0040 mw sa420000+4242000
PT tt##........