To Next PageTo Next PageWhy can't I activate purge mode on my Dentsply Sirona Cavitron 300?
If the Dentsply Sirona Dental equipment purge mode cannot be activated, consider the following: * Be sure the Purge Icon is depressed until activation. * Ensure the Foot Control is released to activate the Purge function. * Turn the Lavage Control to the maximum setting for better purge water flow, as the Handpiece Lavage Control may be set too low.
How to change ultrasonic preset power modes on Dentsply Sirona Dental equipment?
If the Dentsply Sirona Dental equipment ultrasonic preset power modes cannot be changed, it could be because the power preset icons were not programmed properly. Set the desired power level by sliding the power level icon along the scale or tapping the scale where desired.
Why can't I access ultrasonic preset power modes on my Dentsply Sirona Cavitron 300?
If the Dentsply Sirona Dental equipment ultrasonic preset power modes cannot be accessed, it might be because the Preset Power icon was not pressed properly. Press the center of the Preset Power icon for positive activation.
What does Service Indicator 1 on my Dentsply Sirona Cavitron 300 mean?
If the Dentsply Sirona Dental equipment shows Service Indicator 1 in the upper left of the main screen, it could be due to: * The Steri-Mate™ (360) not being installed on the end of the handpiece cable assembly. Install the Steri-Mate™ (360) on the handpiece cable and activate the Foot Control. * An open coil or connection on the Steri-Mate™ (360) handpiece. Replace the Steri-Mate™ (360) with a known good one. * An open connection on the handpiece cable assembly. Replace the handpiece cable assembly. * A problem in the PC board(s). Return Cavitron® 300 Series scaler to Dentsply Sirona Preventive SBU Product Service for factory certified service.
Why can't I change the ultrasonic power level on my Dentsply Sirona Dental equipment touch screen?
If the Dentsply Sirona Dental equipment ultrasonic power level cannot be changed by sliding a finger along the touch screen, it could be because the screen is dimmed and locked. Depress the padlock icon at the lower left of the main screen to unlock it.
Why is my Dentsply Sirona Cavitron 300 handpiece leaking water during operation?
If you're experiencing a water leak from the handpiece of your Dentsply Sirona Dental equipment while in operation, it could be due to: * A worn O-ring on the insert. Replace the O-ring with genuine Cavitron® O-rings. * A water leak in the handpiece water tubing at the handpiece or inside the Steri-Mate™ (360) Handpiece. Replace the Steri-Mate™ (360) handpiece and/or cable assembly.
Why is Tap-On Technology not working on my Dentsply Sirona Dental equipment?
If the Dentsply Sirona Dental equipment Tap-On Technology is not working, consider the following: * Ensure the Foot Control is tapped quickly. If the Foot Control is not tapped quickly, the Tap-On Technology will not operate. * Check if Tap-On Technology is disabled. Press and hold the Settings Icon for approximately two (2) seconds. * A sensor in the handpiece holder prevents the Tap-On Technology from operating when the handpiece is in the holder. * Ensure the insert is secured in the handpiece. Fully seat the insert.
Why won't the purge mode activate on my Dentsply Sirona Cavitron 300 Dental equipment?
If the Dentsply Sirona Dental equipment purge mode does not activate, consider the following: * Ensure the Steri-Mate™ (360) is installed on the handpiece cable assembly. * Replace the Steri-Mate™ (360) with a known good handpiece, as there may be an open coil or connection on the Steri-Mate™ (360) handpiece. * Replace the handpiece cable assembly, as there may be an open connection on the handpiece cable assembly. * Return the Cavitron® 300 Series scaler to Dentsply Sirona Preventive SBU Product Service for factory certified service, as there may be a problem in the PC board(s).
Why can't I install inserts properly in my Dentsply Sirona Cavitron 300 handpiece?
If you cannot install inserts properly in the handpiece of your Dentsply Sirona Dental equipment, here are a few potential causes: * The O-ring on the insert may be dry. Lubricate the O-ring with water. * The O-ring installed on the insert might be incorrect or damaged. Replace the insert O-ring with Cavitron® O-rings. * Metal P-Style inserts are not compatible with Steri-Mate™ (360) handpieces. Use Cavitron inserts with plastic or soft grips, or use regular Steri-Mate™ handpieces.
Why is the water spray not covering the operating area of my Dentsply Sirona Dental equipment tip?
If the water spray from the Dentsply Sirona Dental equipment insert is not properly covering the operating area of the activated tip, it could be due to: * Improper water flow adjustment. Refer to “Cavitron® 300 Series Directions for Use” for instructions on water flow adjustment. * A partially clogged insert. Replace the insert.
General| Type | Ultrasonic Scaler |
|---|---|
| Frequency | 30 kHz |
| Water Flow Adjustment | Yes |
| Power Adjustment | Yes |
| Voltage | 100-240V |
| Frequency (Electrical) | 50/60 Hz |
| Tip Compatibility | Cavitron Inserts |
| Foot Control | Yes |
General safety and operational guidelines for the Cavitron system to prevent damage or malfunction.
Safety measures to be followed during dental procedures using the ultrasonic scaler.
Practicing infection control procedures for operator and patient safety with the ultrasonic scaler.
Conforming to CDC/ADA standards for dental water supply systems and infection control.
Specifications for incoming water supply line pressure and temperature for system installation.
Power requirements for the ultrasonic scaler system, including voltage and amperage.
Steps for unpacking the ultrasonic scaler system and verifying all components and accessories.
Guidelines for properly positioning and connecting the Cavitron system base unit.
Instructions for connecting the AC power cord to the system and a wall outlet.
Overview of the main system controls and their functions, including diagnostic display.
Explanation of the diagnostic display indicators and controls on the main and settings screens.
Details on the 360 rotating handpiece nose, handpiece cable, and their features.
Information on Cavitron 30K ultrasonic inserts, including tip shape, O-ring, and connecting body.
Instructions for using the Tap-On foot pedal in Tap-On mode and enabling/disabling the feature.
Details on accessories and user-replaceable parts available for the Cavitron system.
List of accessories included with the Cavitron system, such as power cords and foot pedals.
Details on user-replaceable parts and kits available for the Cavitron system.
Steps for setting up the sterilizable handpiece, connecting it to the cable, and purging air.
Explanation of Boost Mode for temporary increased ultrasonic power and how to activate it.
Guidance on adjusting patient position for optimal access and visibility during scaling procedures.
Procedures for performing ultrasonic scaling, including tip placement, pressure, and lavage adjustment.
Tips for managing patient sensitivity during ultrasonic scaling procedures.
Procedures for daily start-up and between-patient maintenance of the ultrasonic scaler system.
Recommended weekly disinfection procedures, including chemical flushing of waterlines.
Instructions for monthly maintenance of the water line filter and resetting the indicator.
A guide to common symptoms and their solutions for the ultrasonic scaler system.
Contact information and procedures for obtaining technical support and repair services.
