Dentsply Sirona X-Smart IQ User Manual (English)

Other manuals for Dentsply Sirona X-Smart IQ

User Manual74 pages

Directions For Use88 pages

Questions and Answers:

F
felliottAug 20, 2025
What to do if X-Smart IQ® Handpiece won't switch on?
- R
  Robert DeckerAug 20, 2025
  If your Dentsply Sirona Medical Equipment X-Smart IQ® Handpiece does not switch on, there are several possible causes. First, the battery might be completely empty, indicated by all LEDs being off, in which case you should connect the handpiece to the charger. Second, the handpiece may no longer respond, even if the LEDs are lit, meaning you should perform a reset. Finally, the multifunction button could be faulty, in which case you should contact your service center.
A
Aaron DodsonAug 22, 2025
What to do if running Dentsply Sirona Medical Equipment X-Smart IQ® Handpiece cannot be stopped?
- R
  Raymond BeltranAug 22, 2025
  If the Dentsply Sirona Medical Equipment X-Smart IQ® Handpiece cannot be stopped during preparation, it might be due to the ON/OFF button being blocked or faulty. Briefly press the multifunction button once to stop the X-Smart IQ® Handpiece. Then, try starting and stopping the handpiece again. If the issue persists, contact your service center.
D
Daniel ArnoldAug 25, 2025
What to do if rotary endodontic instrument is jammed in root canal with Dentsply Sirona Medical Equipment?
- S
  Stephen TaylorAug 25, 2025
  If a rotary endodontic instrument has become jammed in the root canal when using Dentsply Sirona Medical Equipment, it indicates that the treatment was not performed properly. Select reverse rotation, start X-Smart IQ® Handpiece and carefully rotate the endodontic instrument out of the root canal.
P
Peggy RiversAug 26, 2025
What to do if reciprocating endodontic instrument is jammed in root canal with Dentsply Sirona Medical Equipment?
- B
  Brittney AllenAug 27, 2025
  If a reciprocating endodontic instrument has become jammed in the root canal when using Dentsply Sirona Medical Equipment, it means that the treatment was not performed properly. Remove the reciprocating endodontic instrument with pliers by carefully rotating clockwise.
H
Heather HoffmanAug 28, 2025
Why Dentsply Sirona Medical Equipment X-Smart IQ® Handpiece is getting hot?
- G
  George EvansAug 28, 2025
  If the Dentsply Sirona Medical Equipment X-Smart IQ® Handpiece is getting hot, it is likely due to overheating. Allow the device to cool down before starting the X-Smart IQ® Handpiece again.
D
davidmendozaAug 30, 2025
What to do if Dentsply Sirona Medical Equipment X-Smart IQ® Contra- angle cannot be calibrated?
- C
  Christopher NavarroAug 30, 2025
  If the Dentsply Sirona Medical Equipment X-Smart IQ® Contra-angle cannot be calibrated, the calibration procedure may have been interrupted by increased resistance in the X-Smart IQ® Contra-angle. If calibration has been interrupted, calibrate X-Smart IQ® Handpiece again to rule out the possibility of a motor fault. Clean and lubricate the X-Smart IQ® Contra-angle. Start the calibration procedure again.
T
Troy FigueroaAug 31, 2025
What to do if Dentsply Sirona Dental equipment handpiece cannot be switched on?
- G
  garciatrevorAug 31, 2025
  If your Dentsply Sirona dental equipment handpiece cannot be switched on, it could be due to several reasons: * The battery may be completely flat. In this case, connect the motor handpiece to the charger. * The handpiece may no longer be responding. If the LEDs are lit but the motor handpiece does not respond when the button is pressed, perform a reset. * The multifunction button could be faulty, causing the motor handpiece to automatically switch to ready mode. Contact your service center for assistance.
M
Mr. John SmithSep 2, 2025
Why is the Dentsply Sirona X-Smart IQ Dental equipment losing connection with iPad Mini?
- K
  Kathryn WardSep 3, 2025
  If you've lost connection between the handpiece and the iPad Mini™ for your Dentsply Sirona dental equipment, here are a few things to check: * The iPad Mini™ may be switched off due to an empty battery. Recharge the iPad Mini™ and reconnect the motor handpiece, or use it in stand-alone mode. * The iPad Mini™ Bluetooth® may be switched off. Turn on the Bluetooth® on the iPad Mini™ and reconnect the motor handpiece. * The motor handpiece may be too far from the iPad Mini™. Place the motor handpiece near the iPad Mini™ and reconnect it.
P
Patrick JonesSep 4, 2025
What to do if Dentsply Sirona X-Smart IQ Dental equipment contra-angle cannot be calibrated?
- L
  Linda FrazierSep 4, 2025
  If the contra-angle of your Dentsply Sirona dental equipment cannot be calibrated, the calibration procedure may have been interrupted by increased resistance in the contra-angle. If calibration has been interrupted, calibrate the motor handpiece again to rule out the possibility of a motor fault. Clean the contra-angle and start the calibration procedure again.
D
Diana MorganSep 6, 2025
What to do if Dentsply Sirona X-Smart IQ handpiece loses connection to iPad?
- S
  schultzalecSep 6, 2025
  If the Dentsply Sirona Dental equipment handpiece loses connection with the iPad, first, check if the iPad battery is empty and needs recharging, or you can use it in stand-alone mode. If the iPad's Bluetooth is off, switch it on and reconnect the motor handpiece. Also, make sure the motor handpiece is near the iPad when reconnecting.

Dentsply Sirona X-Smart IQ Specifications

General

Type	Endodontic motor
Connectivity	Bluetooth
Integrated Apex Locator	Yes
Battery	Lithium-ion
Cordless Operation	Yes
Charging Time	Approximately 2 hours
Programs	Customizable programs
Autoclave Compatibility	Handpiece is autoclavable
Motor Type	Brushless DC Motor
Motor Rotation	Reciprocating and continuous