EasyManua.ls Logo

Despatch LBB 2-12 - User Manual

Default Icon
65 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
LBB Series Oven Owner’s Manual PREFACE
Version 20
LBB SERIES OVEN
OWNER’S MANUAL
C-188
PN 336979
VERSION 20
4/2018

Table of Contents

Questions and Answers

  • E
    ericwellsAug 19, 2025
    Why is my Despatch Oven not heating up properly?
    • A
      Austin CurryAug 19, 2025
      If your Despatch Oven fails to heat or only reaches 30–50 °C, there are several potential causes. First, check the power source, oven, and wall fuses. A burned-out heater element could also be the reason, in which case it should be replaced. A Control Instrument malfunction could be the problem; check the control parameters and replace the controller if the OUT LED does not turn on. Lastly, inspect for loose wire connections behind the control panel after disconnecting the power.
  • B
    Brian EllisAug 21, 2025
    Why does my Despatch Oven heat up so slowly?
    • S
      smartinAug 21, 2025
      Several factors can cause a Despatch Oven to heat up slowly. An improperly loaded workload, low line voltage, one or two burned-out heating elements, a wide-open vent, or fan motor failure. To address this, reduce the load or redistribute it within the chamber. Ensure sufficient power and proper connections, checking for circuit overload. Verify heater amperage and replace any burned-out elements. Close the vent. Finally, consider replacing the fan motor.
  • S
    Steven WhiteAug 23, 2025
    What causes frequent heater element burnout in my Despatch Oven?
    • T
      Thomas BurgessAug 25, 2025
      Frequent heater element burnout in a Despatch Oven can stem from several causes. Harmful fumes generated by the load, spillage on heater elements, overheating, or fan motor failure. Increase the vent opening or discontinue the process if fumes are the issue. Disconnect power and clean the oven chamber and elements if there's spillage. Check the Control and High Limit instruments if the oven is overheating. Replacing the fan motor might be necessary.
  • J
    James HillAug 26, 2025
    What to do if Despatch Oven will not control at Setpoint?
    • E
      Ethan DawsonAug 26, 2025
      If your Despatch Oven isn't controlling at the setpoint, it could be due to a High Limit instrument set too low, a Control instrument malfunction, or air friction from the recirculation fan. Try setting the High Limit higher. Check control parameters before replacing the Control instrument. Also, open the exhaust air vent, as the unit won't control at the minimum operating temperature with the vent closed.
  • S
    Sara BrownAug 28, 2025
    How to fix inaccurate temperature in Despatch Oven?
    • C
      christophergrantAug 28, 2025
      An inaccurate temperature in your Despatch Oven is likely due to control instrument miscalibration. Check the control parameters and recalibrate the Control instrument.
  • L
    lisa63Aug 30, 2025
    Why is the temperature in my Despatch Oven so erratic?
    • C
      Cory JohnsonAug 30, 2025
      Erratic temperature in your Despatch Oven is caused by control instrument malfunction. Check control parameters before replacing the Control instrument.
  • M
    Michael WilliamsSep 1, 2025
    What to do if heater in Despatch Oven doesn't shut down until temp. reaches the High Limit setting?
    • A
      afisherSep 2, 2025
      If the heater in your Despatch Oven doesn't shut down until the temperature reaches the High Limit setting, it could be due to a Control instrument malfunction or an SSR Relay malfunction. Verify the control parameters and replace the control instrument if no output exists. If control output exists, replace the relay.
  • T
    Tracy PearsonSep 4, 2025
    Why is the surface or door temperature of my Despatch Oven excessively high?
    • E
      Erik RossSep 4, 2025
      Excessive surface or door temperature in a Despatch Oven can be caused by door seal deterioration or the door being closed into only the top or bottom latch. Replace the door seal. Ensure that the latch strike is contacting center of latch. Adjust mounting angle as required. Adjust door for even top and bottom latch tension by turning screws on ends of latch. Clockwise increases tension on latch. Counterclockwise decreases tension.
  • J
    James AdamsSep 6, 2025
    How to fix improper airflow in Despatch Oven?
    • S
      Sabrina JohnsonSep 6, 2025
      Improper airflow in a Despatch Oven can result from fan motor failure or an unbalanced fan wheel. Replace the fan motor. Reposition the fan wheel within 3/10” from the top of the housing or replace the fan wheel.
  • K
    Kevin RyanSep 8, 2025
    What causes excessive vibration in my Despatch Oven?
    • S
      Suzanne LeonSep 8, 2025
      Excessive vibration in a Despatch Oven can be attributed to a dirty or unbalanced fan wheel. Clean the fan. Replace the fan wheel.

Summary

About This Manual

Important User Information

Crucial operational and safety guidance for users.

Technical Specifications

Power Requirements

Specifies voltage, amperage, and connection types.

Safety Precautions

General Safety Information

Important warnings and compliance requirements for oven operation.

Lockout Requirements

Specific rules for safely de-energizing equipment.

Lockout Procedure

Detailed steps for safely de-energizing equipment for maintenance.

Maintenance and Electrical Safety

Safety rules for performing maintenance and handling electrical power.

Fire Prevention and Response

Procedures to prevent fires and actions to take if a fire occurs.

Equipment Lockout Requirements

Mandates lockout for inspection and repair to prevent injury.

Emergency Stop

How to stop the oven immediately in case of risk.

Disconnecting Devices

Power Disconnection Methods

Theory of Operation

Control System Overview

Primary Control Instrument Details

Operation of the main temperature controller.

High Limit Instrument Function

Role of the high limit instrument in protecting oven and product.

Product vs. Oven High Limit

Assembly and Setup

Unpacking and Inspection

Oven Setup and Placement

Guidelines for selecting location and preparing the oven for use.

Set-up Procedure

Wiring and Power Connections

How to connect the oven to the electrical supply.

Oven Operation

Pre-Startup Checklist

Standard Operating Procedure

Steps for starting and running the oven with standard controls.

Starting the Oven

Using the Control Instrument

Instructions for interacting with the oven's control system.

Changing Temperature Setpoint

How to adjust the desired operating temperature.

Control Parameter Programming

Advanced settings for the primary control instrument.

Accessing Setup Mode

Oven Zone Calibration

Setting the High Limit Temperature

Configuring the safety temperature cutoff.

Adjusting High Limit Setpoint

How to modify the high limit temperature value.

High Limit Parameter Setup

Maintenance Procedures

Regular Maintenance Checklist

Routine Functional Tests

Testing the High Limit Instrument

Replacing the Control Instrument

Step-by-step guide for replacing the main controller.

Replacing the High Limit Instrument

Step-by-step guide for replacing the safety temperature controller.

Replacing the Heater Unit

Troubleshooting Guide

DES2000 Control Parameter Check

High Limit Instrument Reset

Despatch LBB 2-12 Specifications

General IconGeneral
BrandDespatch
ModelLBB 2-12
CategoryOven
LanguageEnglish

Related product manuals