DEVI DEVIreg 535 Programming Instructions

Phone 1800 636 091 • Email info@devi.com.au • Web www.devi.com.au
Devireg
™
535
Programming Instructions
Introduction
The devireg™ 535 allows you to program your heating system by using pre-set program modes. Follow the steps
below to ensure the most desireable outcome to suit your heating requirements. The first step is to configure the
thermostat:
• Ifyourdevireg™535hasnotalreadybeenconguredbyanelectricianorinstaller,gotothesection“Conguringthe
Thermostat”.Otherwise,skipthisstep.
• Afteryourdevireg™535hasbeencongured:Thereare4programmodestochoosefrom.Dependingonyourrequirements,
gotoeitherthesection“ManualMode”or“ProgramMode”andfollowthestepsprovidedtosetupyourthermostat.
Configuring the Thermostat
If your thermostat has already been configured by your installer or electrician, there is no need to configure
the thermostat.
1
Remove
front cover
Tocongureorre-congureyourthermostat,youwillneedtoremovethefrontcover.Dependingonthetypeofcover,
themethodofremovalisslightlydifferent.Refertotheimagesaboveforguidance.
Snap-lock Devireg
™
535 Front Cover:
Insertapaperclipintotheslot(asshowninthediagramabove)tosnap-releasethecover.Gentlysqueezebothsidesof
thecoverwhilstremovingit.Pressthetopcircularbuttonlocatedontherighthandsideofthethermostatwithapencil.
Original Devireg
™
535 Front Cover (if no slot on the bottom of the cover):
Withasmallscrewdriver,gentlypressthereleasetabsonbothsidesofthethermostat(thirdgroovefromthebottom),
thenremovethecover.Pressthetopcircularbuttonlocatedontherighthandsideofthethermostatwithapencil.
2
Select
sensor mode
Ifyourunderoorheatingisinabathroomorwetarea,werecommendyouselecttheoorsensormode .Ifitisinadry
arealikeabedroomorlivingroom,werecommendoorandroomsensormode .Tochangetheselectionpressthe
Select(•)buttonandthenusethearrows()untilthecorrectsymbolsappear.ThenpresstheSelect(•)buttontosave.
Moveontothenextscreenbyusingtherighthandarrow().Ifyouhavechosenroomsensormode,gotoStep5.
3
Select
maximum
floor
temperature
Themaximumoortemperaturesettingshouldnowbedisplayedonthescreen.Tochangethesetting,pressthe
Select(•)button.Setthetemperaturebyusingthearrows()andthenpresstheSelect(•)buttontoselect.
Dependingonyouroorstructureandoorcovering,werecommendthefollowing:
FloorConstruction Tiles Timber Carpet
Timberbase 32°C 27°C 30°C
ConcreteorF/Cbase 45°C 27°C 40°C
Nowmovetothenextscreenbypressingtherighthandarrow().Ifyouhavechosenoorandroomsensormode,
gotoStep5.
4
Choose the
scale
Werecommendusing“°C”foroorandroomsensingorroomsensingonly,or1-6foroorsensingonly.Tochange
thecurrentsetting,presstheSelect(•)buttonandchangeusingthearrows(),thenpressSelect(•)tosave.
5
Save your
selection
Pressthetopcircularbuttonwithapenciltogobacktotheoriginalscreen.Replacethefrontcover.
TimePeriods(“Morning”,
“Day”,“Evening”&“Night”)
Weekdays
Settings
Room
Sensor
Floor
Sensor
Actual
Temperature
isdisplayed
Childproof
Frost
Protection
Maximum/
Minimum
HeatIndicator:
Red:Heating
Green:Attemperature
Note:Thisisthemaximum
temperature,notyourpreferred
operatingtemperature.
BROCDEV002.4
Snap-lock Devireg
™
535 Original Devireg
™
535
third
groove

DEVI DEVIreg 535 Specifications

General

Brand	DEVI
Model	DEVIreg 535
Category	Thermostat
Language	English