DeVilbiss Air Power Company 3540CWHP

Questions and Answers

A
ashleyjohnsonJul 29, 2025
Why is my DeVilbiss Air Power Company 3540CWHP Pressure Washer leaking oil at the pump?
- J
  Julie RamirezJul 29, 2025
  If your DeVilbiss Air Power Company Pressure Washer is leaking oil at the pump, there are several potential causes. The oil seals might be worn, the drain plug could be loose, or the fill plug o-ring might be worn. It's also possible that the pump is overfilled or the incorrect type of oil was used. In the case of worn oil seals, it is recommended to have them replaced by an Authorized Warranty Service Center (AWSC). For a loose drain plug, simply tighten it. If the fill plug o-ring is worn, check and replace it. If the pump is overfilled, check for the correct amount of oil. Finally, if the incorrect oil was used, drain the pump and fill it with the correct amount and type of oil.
C
claytonmelanieAug 3, 2025
What causes water leaking at the pump of my DeVilbiss Air Power Company 3540CWHP Pressure Washer?
- D
  Diane LynchAug 3, 2025
  If water is leaking at the pump of your DeVilbiss Air Power Company Pressure Washer, first check for loose connections and tighten them. If the piston packings are worn, it is recommended to have them replaced by an Authorized Warranty Service Center (AWSC).
E
Emily RoseAug 13, 2025
What to do if my DeVilbiss Air Power Company 3540CWHP Pressure Washer will not draw chemicals?
- A
  Andrew JonesAug 13, 2025
  If your DeVilbiss Air Power Company Pressure Washer is not drawing chemicals, make sure the low-pressure nozzle is properly installed in the wand. Check the chemical filter for clogs and clean it if necessary. Also, ensure the chemical hose is fully submerged in the chemical solution.
J
justinphamAug 18, 2025
How to fix water leaking at gun to wand connection on DeVilbiss Air Power Company 3540CWHP?
- J
  jreyesAug 18, 2025
  If the DeVilbiss Air Power Company Pressure Washer is leaking water at the gun to wand connection, it might be due to a worn o-ring. Check and replace the o-ring if necessary. It could also be due to a loose hose connection. Try tightening the connection. If the leak persists, disassemble the connection, apply thread sealing tape to the threads, and reassemble.
J
Jonathan YoungAug 23, 2025
Why does my DeVilbiss Air Power Company 3540CWHP have low pressure after normal use?
- J
  John KingAug 23, 2025
  If your DeVilbiss Air Power Company Pressure Washer has no or low pressure after a period of normal use, it may be due to worn seals or packings, or worn or obstructed valves. In both cases, it is recommended to have them replaced by an Authorized Warranty Service Center (AWSC).
B
Brian BrownNov 7, 2025
Why is there no or low pressure on my DeVilbiss Air Power Company 3540CWHP Pressure Washer when I first use it?
- M
  Monica WeaverNov 7, 2025
  If your DeVilbiss Air Power Company Pressure Washer isn't providing the expected pressure initially, several factors could be at play. First, ensure you've selected the correct nozzle. Insufficient water supply might be the issue; the water supply must be at least 5 GPM at 20 PSI. Check for any leaks in the high-pressure hose and repair them, applying thread sealing tape if needed. A clogged nozzle can also cause this, so clean it with the nozzle cleaning tool and flush out any obstructions with clean water. The water filter screen might be clogged, requiring removal and cleaning. In case of a defective E-Z start valve, consult an Authorized Warranty Service Center (AWSC). Finally, trapped air in the hose can be the culprit; turn off the engine and water supply, disconnect the water supply...