DeVilbiss Air Power Company EXHA2425-WK

Questions and Answers

N
nathan46Aug 5, 2025
How to troubleshoot starting issues in DeVilbiss Air Power Company EXHA2425-WK?
- L
  Logan WhiteheadAug 5, 2025
  To troubleshoot why your DeVilbiss Air Power Company Pressure Washer engine won't start, consider these potential causes: * **No fuel:** Add fuel. * **Low oil:** Add the required amount of oil if your model has a low oil shutdown feature. * **Pressure build-up:** Squeeze the gun trigger to relieve pressure. * **Priming/Choking Issues:** Push the primer bulb 3 times or choke the engine. * **Spark Plug Wire:** Attach the spark plug wire. * **Engine ON/OFF Switch:** Ensure the engine ON/OFF switch is in the ON position. * **Choke lever position:** Move the choke to the “No Choke” position if the engine is hot. * **Fuel valve position:** Move the fuel valve lever to the “Open” position if your equipment is equipped with one.
J
jburnsAug 15, 2025
Why does my DeVilbiss Air Power Company EXHA2425-WK have low pressure after normal use?
- R
  Roger HensleyAug 15, 2025
  If your DeVilbiss Air Power Company Pressure Washer has no or low pressure after a period of normal use, it could be due to: * **Worn seal or packing:** Have it replaced by an AWSC. * **Worn or obstructed valves:** Have them replaced by an AWSC. * **Worn unloader piston:** Have it replaced by an AWSC. * **Worn E-Z start valve:** Have it replaced by an AWSC.
R
robin71Aug 19, 2025
What to do if DeVilbiss Air Power Company EXHA2425-WK Pressure Washer will not draw chemicals?
- D
  Dennis LopezAug 20, 2025
  If your DeVilbiss Air Power Company Pressure Washer won't draw chemicals, consider these possible causes: * **Wand setting:** Refer to the 'How to Use Wand' paragraph in the Operation Section. * **Chemical filter:** Clean the chemical filter. * **Chemical screen:** Ensure the end of the chemical hose is fully submerged in the chemical. * **Chemical thickness:** Dilute the chemical if it is too thick. * **Pressure hose length:** Lengthen the water supply hose instead of the pressure hose. * **Chemical build-up:** Have the parts cleaned or replaced by an AWSC.
M
Mr. Michael AndersonAug 25, 2025
What to do if water leaking at gun or wand connection of DeVilbiss Air Power Company EXHA2425-WK?
- H
  Heather DoyleAug 25, 2025
  If water is leaking at the gun/wand connection of your DeVilbiss Air Power Company Pressure Washer, it might be due to: * **Worn or broken o-ring:** Try tightening the connection, and check/replace the o-ring. * **Loose hose connection:** Check and replace if necessary.
A
Amanda BuchananAug 30, 2025
Why is my DeVilbiss Air Power Company EXHA2425-WK Pressure Washer leaking water at the pump?
- J
  John NolanAug 30, 2025
  If water is leaking at the pump of your DeVilbiss Air Power Company Pressure Washer, the cause may be: * **Loose connections:** Tighten the connections. * **Worn piston packings:** Have them replaced by an AWSC. * **Worn or broken o-rings:** Have them replaced by an AWSC. * **Damaged pump head or tubes:** Have them replaced by an AWSC.
B
Bobby HendrixNov 9, 2025
Why is there no or low pressure in my DeVilbiss Air Power Company Pressure Washer?
- A
  andreamorseNov 9, 2025
  If your DeVilbiss Air Power Company Pressure Washer has no or low pressure upon initial use, consider the following: * **Wand setting:** Refer to the 'How to Use Wand' paragraph in the Operation Section. * **Water supply:** Ensure your water supply is at least 5 GPM @ 20 PSI. * **Leaks:** Repair any leaks at the high-pressure hose. * **Nozzle:** Clean the nozzle with a paper clip or nozzle cleaning tool, and flush out any obstructions with water. * **Water filter screen:** Remove and clean the filter. * **E-Z start valve:** Check with an Authorized Warranty Service Center (AWSC) if you suspect a defective valve. * **Air in hose:** Turn off the engine and water source, disconnect the water source, turn the water on to remove air, then reconnect and squeeze the trigger. * **...