DeWalt D51256 Manual

96 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

1

®

D51256

D51275

D51256.P65 28-12-2001, 09:211

Other manuals for DeWalt D51256

Instruction Manual7 pages

User Manual96 pages

Questions and Answers:

T
Todd PadillaAug 19, 2025
What to do if fasteners jam in my DeWalt Nail Gun?
- A
  Alejandra BlackAug 19, 2025
  If fasteners are jamming in your DeWalt Nail Gun, it could be due to a few reasons. The driver channel in the nose piece might be worn, requiring a nosepiece replacement. Ensure you're using the correct size and angle fasteners. A loose magazine can also cause jams, so check that the magazine latch is holding firmly. Lastly, a worn driver blade can lead to jamming, so consider replacing the Driver Blade Kit (Cat. # D512565 for 16 GA., D512752 for 15 GA.).
S
Sabrina WeeksAug 21, 2025
Why does my DeWalt D51256 lack power and feel sluggish?
- P
  petersonthomasAug 21, 2025
  If your DeWalt Nail Gun is showing a lack of power, it could be due to several factors: * Low air pressure: Check your air supply. * Lack of lubrication: Lubricate the tool using approved pneumatic tool oil. * Damaged or worn O-rings: Replace the gasket/O-rings using O-ring Repair Kit Cat. # D512561 (16 GA.), D512751 (15 GA.). * Blocked exhaust port: Disconnect the air, remove the exhaust plate from the top of the tool, and clean the port.
L
lbrooksAug 25, 2025
Why is my DeWalt D51256 Nail Gun skipping nails?
- T
  Thomas ScottAug 25, 2025
  If your DeWalt Nail Gun is skipping nails, the issue could stem from several causes. First, ensure the air supply and couplers are not restricted. Lack of lubrication can also cause this, so lubricate the tool with approved pneumatic tool oil. Check if the nose piece screws are loose and tighten them with the appropriate Allen wrench. Make sure you are using the recommended size and angle fasteners. A dirty magazine can also cause this issue, so clean the magazine track and nosepiece. If the magazine is worn, consider replacing it. Finally, a broken or damaged driver blade can also be the culprit, so replace the Driver Blade Kit (Cat. # D512565 for 16 GA., D512752 for 15 GA.).
H
heather97Aug 26, 2025
Why does my DeWalt D51256 Nail Gun lack power?
- K
  Kyle PerryAug 26, 2025
  If your DeWalt Nail Gun is showing a lack of power or is sluggish, several factors could be the cause. Begin by checking the air supply to ensure it's not low. Insufficient lubrication can also lead to this issue, so lubricate the tool with approved pneumatic tool oil. Damaged or worn O-rings can also cause this problem; replace them using the O-ring Repair Kit (Cat. # D512561 for 16 GA., D512751 for 15 GA.). Lastly, a blocked or clogged exhaust port can restrict performance. To resolve this, disconnect the air, remove the exhaust plate from the top of the tool, and clean the port.
L
leeaaronAug 27, 2025
Why is my DeWalt D51256 Nail Gun not cycling?
- J
  joshuahowellAug 27, 2025
  If your DeWalt Nail Gun is not cycling, there are several potential causes. First, check that the tool is receiving air. If it's cold weather, warming up the tool might help. Damaged or worn O-rings can also prevent cycling; replace them using the O-ring Repair Kit (Cat. # D512561 for 16 GA., D512751 for 15 GA.). Lastly, a broken or damaged driver blade could be the issue; replace the Driver Blade Kit (Cat. # D512565 for 16 GA., D512752 for 15 GA.).
C
cthompsonAug 29, 2025
Why is my DeWalt Nail Gun leaking air around the nose when actuated?
- M
  Mark MosesAug 29, 2025
  If you notice air leaks around the nose of your DeWalt Nail Gun when the tool is in the actuated position (driver blade down), it's likely due to a damaged or worn bumper. To fix this, replace the bumper using the Bumper Kit (Cat. # D512566 for 16 GA., D512753 for 15 GA.).
J
Jennifer FieldsAug 31, 2025
Why is my DeWalt Nail Gun leaking air around the nose at rest?
- M
  maria86Aug 31, 2025
  If your DeWalt Nail Gun leaks air around the nose when at rest (driver blade in the up position), the cause is likely damaged or worn O-rings. Replace the gasket/O-rings using the O-ring Repair Kit (Cat. # D512561 for 16 GA., D512751 for 15 GA.) to resolve this issue.
I
Ivan CarsonSep 2, 2025
How to fix air leaks from the top cap of my DeWalt D51256 Nail Gun?
- J
  John TranSep 2, 2025
  If the top cap of your DeWalt Nail Gun is leaking air, there are a couple of potential causes. First, check if the cap screws are loose and tighten them using the appropriate Allen wrench. If the screws are tight, the issue might be a damaged or worn gasket or O-ring. In this case, replace the gasket/O-rings using the O-ring Repair Kit (Cat. # D512561 for 16 GA., D512751 for 15 GA.).
S
Savannah GallagherSep 5, 2025
What to do if there are air leaks around the nose of my DeWalt D51256 Nail Gun when actuated?
- T
  Todd GraySep 5, 2025
  If you notice air leaks around the nose of your DeWalt Nail Gun when it's in the actuated position, it's likely due to a damaged or worn bumper. Replace the bumper using Bumper Kit Cat. # D512563 (16 GA.), D512753 (15 GA.).
J
Jerry KempSep 6, 2025
Why is my DeWalt D51256 Nail Gun leaking air around the nose when at rest?
- K
  kennedymicheleSep 7, 2025
  If your DeWalt Nail Gun leaks air around the nose when at rest, the O-rings are likely damaged or worn. Replace the gasket/O-rings using O-ring Repair Kit Cat. # D512561 (16 GA.), D512751 (15 GA.).

DeWalt D51256 Specifications

General

Brand	DeWalt
Model	D51256
Category	Nail Gun
Language	English

Related product manuals

Preview: DeWalt D51257

Preview: DeWalt D51256K

Preview: DeWalt D51238

Preview: DeWalt D51276

Preview: DeWalt D51236

Preview: DeWalt D51275

Preview: DeWalt D51844

Preview: DeWalt D51823

Preview: DeWalt D51845

Preview: DeWalt D51825

DeWalt D51850-XE

Preview: DeWalt D51825-XE

DeWalt D51825-XE