DeWalt DCD792 - Page 14

12
ENGLISH
Proper hand position requires one hand on the top of the drill as
shown, with the other hand on the main handle
16
.
Screwdriver Operation (Fig.E)
1. Turn the torque adjustment collar
3
to the desiredposition.
2. Select the desired speed/torque range using the
gear shifter
4
to match the speed and torque of the
plannedoperation.
NOTE: Use the lowest torque setting required to seat the
fastener at the desired depth. The lower the number, the
lower the torqueoutput.
3. Insert the desired fastener accessory into the chuck as you
would any drillbit.
4. Make some practice runs in scrap or on unseen areas to
determine the proper position of the clutchcollar.
your tool to allow you to configure specific tool functions. Refer
to ModeSelector.
NOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by
DeWALT
is under license. Other trademarks and
trade names are those of their respectiveowners.
NOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobileapplication.
Download the
DeWALT
Tool Connect™ applicationat:
• Install a fully charged 18V battery pack into the tool. Refer to
Inserting and Removing the Battery Pack from theTool.
• Follow the instructions in the app to create your Tool
Connect™account.
• On the Home screen of the app, select "+ Tool" to begin the
process of adding your tool to theapp.
• To connect your tool with the
DeWALT
Tool Connect™
app, at the appropriate screen, press the mode selector
button
12
for 3–5 seconds, then wait for the tool to
connect. The tool can only be connected to one Tool
Connect™ account at atime.
• Once the tool has been connected, you can confirm that
you would like to register theproduct.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your local
DeWALT
service center. Do not attempt to replace the coin cell
batteryyourself.

WARNING: Danger of explosion if battery is
incorrectlyreplaced.

WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2hours and can lead
todeath.
• Keep new and used batteries away from children. If
the battery compartment does not close securely, stop
using the product and keep it away fromchildren.
• If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medicalattention.
Proper Hand Position (Fig.K)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicableregulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
• If the coin cell battery contents come into contact
with the skin, immediately wash area with mild soap
and water. If coin cell battery liquid gets into the eye,
rinse water over the open eye for 15minutes or until
irritation ceases. If medical attention is needed, the
battery electrolyte is composed of an organic solvent
and lithiumsalts.
• Do not incinerate or dispose of tool together with
household waste material! Tool that has reached
the end of its life must be collected separately
and returned to an environmentally compatible
recyclingfacility.
TABLE 1
Customizable Features Home
Factory Presets
Customizable RangeMode 1 Mode 2 Mode 3
Worklight brightness MED OFF MED HIGH OFF‑HIGH
Worklight delay off 20 secs 20 secs 20 secs 20 minutes 0–20 minutes
Maximum speed (RPM) Speed 1
Speed 2
550
2000
550
2000
550
2000
550
2000
180–550
600–2000