EasyManuals Logo

DeWalt DCMASBC1 User Manual

DeWalt DCMASBC1
12 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #9 background imageLoading...
Page #9 background image
7
ENGLISH
Brush Cutting (Fig. F, G)
With the brush cutter on, angle it and swing side to side as
shown in Fig.F.
Maintain a minimum distance of 24" (610mm) between the
guard and your feet as shown in Fig.G.
WARNING: Keep the rotating blade roughly parallel with
the ground (tilted no more than 30°). This trimmer is not
an edger. DO NOT TILT the brush cutter so that the blade
is spinning near a right angle to the ground. Flying debris
can cause seriousinjury.
Helpful Cutting Tips
Use the tip of the blade to do the cutting; do not force tool
head into uncutgrass.
WARNING: Hold the tool using only the designated
gripping surfaces: The powerhead handle and the
auxiliary handle.
WARNING: Do not use the pole as a grippingsurface.
Proper hand position requires one hand on the powerhead
handle
13
and one hand on the auxiliary handle
14
.
Proper Hand Position (Fig. A, E)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicableregulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
Attaching and Adjusting the Shoulder Strap
(Fig. E)
WARNING: The shoulder strap should only be slung over
one shoulder and not across thebody.
WARNING: Use of a shoulder strap
10
is required while
using thistool.
Attach the strap to the tool as shown in Fig. E and adjust for
proper balance and support.
1. Attach the strap mount.
2. Snap the shoulder strap latch
12
onto the strap
mount
11
located on the unit, just in front of the ON/OFF
trigger as shown in Fig.E. Adjust the strap so it fits over
yourshoulder and provides proper balance andsupport.
Assembling the Brush Cutter Attachment to
the Powerhead (Fig. A, B)
1. When installing the brush cutter attachment
1
into the
upper powerhead pole
7
, align the latching button
8
with
the main hole
9
as shown in Fig. B.
2. Lock the knob
6
.
3. When properly assembled, it should look like Fig. B.
Powerhead (Fig. B)
(DCMAS5713 sold separately)
WARNING: To reduce risk of injury:
Before any use, be sure everyone using this unit
reads and understands all manufacturer's safety
instructions and other information contained in
manufacturer'smanual.
Never apply power without an attachment being
properly mounted to thepowerhead.
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories, or prior to
cleaning. An accidental start‑up can causeinjury.
Your attachment is designed such that the powerhead can
separate from the brush cutter attachment by releasing the
knob
6
and gently pulling them apart by their poles
1
,
7
.
This should only be done with the power switch off and the
battery pack removed. Inside the upper powerhead pole
7
is a
mechanical coupling that will spin if the powerhead is turned
on. This coupling can cause severe injury if contacted while the
powerhead isoperating.
NOTE: DO NOT operate the brush cutter attachment WITHOUT
the barrier properly assembled to the powerhead pole.
NOTE: A double shoulder harness is required if the mass of the
tool and battery pack exceed 7.5kg.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
WARNING: Use only DeWALT battery packs andchargers.
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
withoutsupervision.
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the DeWalt DCMASBC1 and is the answer not in the manual?

DeWalt DCMASBC1 Specifications

General IconGeneral
BrandDeWalt
ModelDCMASBC1
CategoryBrush Cutter
LanguageEnglish

Related product manuals