DeWalt DCN692 User Manual (English)

Other manuals for DeWalt DCN692

Instruction Manual26 pages

Manual280 pages

Questions and Answers:

R
Richard RobertsSep 5, 2025
Why does my DeWalt DCN692 motor run but not fire nails?
- P
  peggy13Sep 5, 2025
  If your DeWalt Nail Gun's motor runs but doesn't fire, first check if the dry fire lock out is engaged and load nails into the magazine. Next, verify the battery charge level and charge or replace the battery if necessary. If there's a jammed nail, remove the battery, clear the jam, cycle the stall release lever, and manually push the driver blade up if needed before reinserting the battery.
S
Sean Abbott Jr.Aug 25, 2025
Why DeWalt DCN692 Nail Gun operates, but no fastener is driven?
- L
  Lynn HuberAug 25, 2025
  If your DeWalt Nail Gun operates, but no fastener is driven, it could be due to a few reasons. Check if there are nails in the magazine and load them if necessary. Ensure you are using the correct size and angle nails as recommended. Also, inspect the nosepiece and magazine for any debris and clean them if needed.
J
Jessica StewartAug 25, 2025
Why DeWalt Nail Gun motor does not run with contact trip depressed?
- R
  Robin BrownAug 26, 2025
  If your DeWalt Nail Gun motor doesn't run when you depress the contact trip, start by checking if the trigger lock is engaged and unlock it. Another possibility is that the dryfire lockout is engaged, preventing the contact trip from traveling fully; load more nails into the magazine. Also, the tool might be stalled, which locks the motor; rotate the stall release lever to release it. If the driver blade doesn't return, remove the battery and manually push the driver blade back to its home position. Keep in mind that the motor stopping after 5 seconds is normal operation; release and redepress the contact trip.
K
Katherine MercadoAug 27, 2025
Why won't the motor run when I press the trigger on my DeWalt DCN692?
- V
  Valerie HolderAug 27, 2025
  If the motor of your DeWalt Nail Gun doesn't run when you depress the trigger, several factors could be at play. First, ensure the trigger lock isn't engaged. If the tool is stalled, rotate the stall release lever. If the driver blade doesn't return, remove the battery and manually push the driver blade back. For sequential actuation mode, depress the contact trip before firing, or switch to bump mode (DCN692 only). Try resetting the tool's electronics by removing the battery for 3 seconds and reinserting it. Note that the motor will stop running after 5 seconds, which is normal operation; release and redepress the trigger to continue.
T
tsantiagoAug 27, 2025
How to fix a DeWalt Nail Gun that doesn't drive nails all the way in?
- M
  Monica HendersonAug 27, 2025
  If your DeWalt Nail Gun operates but doesn't fully drive fasteners, first check the depth adjustment and set it to a deeper setting. Ensure the tool is firmly applied to the workpiece. If using bump mode with long nails (DCN692 only), switch to sequential mode. Consider the material and fastener length; if stalling occurs, use appropriate materials and fastener lengths. Remove the no-mar tip if it's attached. New tools may require 500–1000 nails to run-in. If driving longer ring shank nails in soft woods or into harder materials in speed 1, adjust the speed setting to position 2.
B
Brandon MezaAug 28, 2025
What to do if my DeWalt DCN692 motor doesn't run when the contact trip is depressed?
- A
  adamstroyAug 28, 2025
  If the motor of your DeWalt Nail Gun does not run when the contact trip is depressed, start by checking if the trigger lock is engaged and unlock it. Also, check if the dry fire lock out is engaged; if so, load more nails into the magazine. If the tool is stalled, rotate the stall release lever. Note that the motor will stop running after 5 seconds, which is normal operation; release and redepress the contact trip to continue.
R
robinsonalishaSep 9, 2025
Why won't my DeWalt DCN692 Nail Gun motor run when I depress the trigger?
- J
  jennifermartinSep 9, 2025
  If the motor of your DeWalt Nail Gun doesn't run when you depress the trigger, first check if the trigger lock is engaged and unlock it. If the tool is stalled, locking the motor, rotate the stall release lever. If the driver blade does not return, remove the battery and manually push the driver blade back. Ensure the tool is not in sequential actuation mode or switch to bump mode. Also, try removing the battery, waiting 3 seconds, and reinserting it to reset the internal electronics. Note that the motor stopping after 5 seconds is normal operation; release and redepress the trigger.
B
benjaminmitchellSep 6, 2025
Why does the drive blade keep getting stuck on my DeWalt Nail Gun?
- D
  douglasjonesSep 6, 2025
  If the drive blade of your DeWalt Nail Gun continues to get stuck in the down position, use the stall release lever and clear any jammed nails. Clean the nose area of any debris. Consider the material and fastener length; if stalling continues, choose a less rigorous application. New tools can take 500–1000 nails for parts to mesh and wear in together. If trying to drive longer ring shank nails in soft woods, or driving ring shank nails into harder materials in speed 1 - adjust speed setting to position 2.
S
Sharon Molina MDSep 4, 2025
Why DeWalt DCN692 Nail Gun drive blade continues to get stuck in down position?
- C
  Cole BellSep 4, 2025
  If the drive blade of your DeWalt Nail Gun continues to get stuck in the down position, it could be due to a jammed nail. Use the stall release lever to clear any jammed nails, and manually return the driver blade if necessary. Another potential cause is debris in the nosepiece; clean the nose area, watching for small pieces of broken nails stuck in the track.
Z
zmorenoSep 1, 2025
How to fix DeWalt DCN692 Nail Gun that does not actuate?
- M
  Michael CainSep 2, 2025
  If your DeWalt Nail Gun's motor runs but doesn't actuate, first ensure the magazine is loaded with nails. Check the battery charge level and replace if necessary. If there is a jammed nail, remove the battery, clear the jam, cycle the stall release lever, and manually push the driver blade up if needed before reinserting the battery pack.

DeWalt DCN692 Specifications

General

Weight	7.8 lbs
Power Source	Battery
Type	Cordless Framing Nailer
Battery	20V MAX*
Nail Diameter	0.113 in
Nail Length	2 to 3.5 inches
Magazine Capacity	55 nails
Firing Modes	Sequential and Bump