To Next PageTo Next Page
Need help?Do you have a question about the DeWalt DCS371P1 and is the answer not in the manual?
General| Quantity per pack | 1 pc(s) |
|---|
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Indicates a practice not related to personal injury, which, if not avoided, may result in property damage.
Keep work area clean and well lit. Do not operate in explosive atmospheres. Keep children and bystanders away.
Match plugs to outlets. Avoid body contact with earthed surfaces. Do not expose to rain or wet conditions. Do not abuse cord.
Stay alert, use common sense. Wear eye protection. Prevent unintentional starting. Remove adjusting key. Do not overreach.
Do not force the tool. Ensure switch works. Disconnect power before adjustments. Store properly. Maintain tools.
Recharge with specified charger. Use only designated battery packs. Keep away from metal objects. Handle leakage carefully.
Have tool serviced by a qualified repair person using only identical replacement parts.
Hold by insulated grips, keep hands clear of blade, ensure components are mounted, handle blade with care.
Wait for full speed, keep handles dry, be alert, check footing, stay clear of falling pieces.
Do not incinerate damaged batteries. Wash skin/eyes if contact occurs. Handle liquid carefully.
Read warnings. Do not operate in explosive atmospheres. Never modify packs. Charge only with DEWALT chargers.
Do not spill liquids. Store in cool, dry locations. Do not store in a tool with trigger locked.
Battery and charger may get warm. Avoid charging when battery pack is below 50°F (+10°C) or above 104°F (+40°C).
Insert battery pack into charger. Red light indicates charging. Remove pack when charging is complete.
Indicator lights show charging status: Charging, Fully Charged, Hot/Cold Pack Delay.
Charger delays charging if battery is too hot or too cold. Charging resumes automatically when temperature is appropriate.
System automatically shuts off tool and charger when battery is fully discharged to prevent damage.
Mount charger securely to wall using screws. Ensure proper screw selection for wall material.
Disconnect charger from power outlet. Clean with dry cloth and non-flammable cleaners.
Best performance between 65°F and 75°F (18°-24°C). Avoid charging in extreme temperatures.
Table shows blade compatibility with workpiece thickness and number of teeth for optimal cutting.
Instructions for aligning blade to guide rollers for proper cutting performance and blade life.
Install brush cap and blade guards for safety. Ensure they are securely attached.
Align and insert battery pack into tool. Release tool from battery pack by pulling release lever.
Warning to reduce risk of injury: turn off and remove battery pack before adjustments or accessory changes.
Position blade on bottom, slip into guide rollers, hold rollers, insert blade into pulleys, tighten tension lever.
Always use proper hand position for safety. Hold securely for anticipation of sudden reaction.
Mount material in vise. Bring work stop into contact. Tilt tool to blade. Avoid sudden impact.
Align blade with motor housing side for straight cuts. Avoid twisting or cocking blade.
Release switch immediately if blade jams to avoid damage.
Use correct blade for material. Never twist blade. Use liquid coolants for band saws. Reduce vibration.
Turn off and remove battery pack before adjustments or accessory changes. Avoid accidental start-ups.
Self-lubricating bearings are used. No periodic lubrication is needed. Contact service center if required.
Blow dirt and dust out with compressed air. Always wear eye protection. Use a dry cloth and mild soap.
Use only DEWALT recommended accessories to reduce injury risk. Contact dealer or service center for availability.
Charger and battery pack are not serviceable. Repairs by DEWALT service centers ensure safety and reliability.
Register for efficient warranty service, confirmation of ownership, and safety notifications.
Covers defects in materials/workmanship for three years. Excludes normal wear, abuse, and unauthorized repairs.
Includes 1 year free service on tools, 2 years on certain battery packs, 3 years on others.
Full refund if not completely satisfied within 90 days of purchase.
Contact DEWALT for free replacement of illegible or missing warning labels.
