DeWalt DCS777T2-QW

28
ENGLISH
3 . Guard against electricshock.
Avoid body contact with earthed surfaces (e.g., pipes, radiators, cookers
and refrigerators). When using the tool under extreme conditions (e.g.,
high humidity, when metal swarf is being produced, etc.), electric safety
can be improved by inserting an isolating transformer or a (FI) earth-
leakage circuit-breaker.
4 . Keep other personsaway.
Do not let persons, especially children, not involved in the work, touch the
tool or the battery and keep them away from the workarea.
5 . Store idletools.
When not in use, tools must be stored in a dry place and locked
up securely, out of reach ofchildren.
6 . Do not force thetool.
It will do the job better and safer at the rate to which it wasintended.
7 . Use the righttool.
Do not force small tools to do the job of a heavy duty tool. Do not use tools
for purposes not intended; for example do not use circular saws to cut tree
limbs orlogs.
8 . Dressproperly.
Do not wear loose clothing or jewellery, as these can be caught in moving
parts. Non-skid footwear is recommended when working outdoors. Wear
protective hair covering to contain longhair.
9 . Use protectiveequipment.
Always use safety glasses. Use a face or dust mask if working operations
create dust or flying particles. If these particles might be considerably hot,
also wear a heat-resistant apron. Wear ear protection at all times. Wear a
safety helmet at alltimes.
10 . Connect dust extractionequipment.
If devices are provided for the connection of dust extraction and collecting
equipment, ensure these are connected and properlyused.
11 . Securework.
Where possible use clamps or a vice to hold the work. It is safer than using
your hand and it frees both hands to operate thetool.
12 . Do notoverreach.
Keep proper footing and balance at alltimes.
13 . Maintain tools withcare.
Keep cutting tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect tools
periodically and if damaged have
them repaired by an authorized service facility. Keep handles
and switches dry, clean and free from oil andgrease.
14 . Disconnecttools.
When not in use, before servicing and when changing accessories such as
blades, bits and cutters, disconnect tools from the powersupply.
15 . Remove adjusting keys andwrenches.
Form the habit of checking to see that adjusting keys and wrenches are
removed from the tool before operating thetool.
16 . Avoid unintentionalstarting.
Do not carry the tool with a finger on the switch. Be sure that the tool is in
the “off” position before pluggingin.
17 . Stayalert.
Watch what you are doing. Use common sense. Do not operate the tool
when you are tired or under the influence of drugs oralcohol.
18 . Check for damagedparts.
Before use, carefully check the machine to determine that it will operate
properly and perform its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting and any
other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized
service centre unless otherwise indicated in this instruction manual. Have
defective switches replaced by an authorized service centre.
Do not use the tool if the switch does not turn it on and off.
Never attempt any repairsyourself.

WARNING! The use of any accessory or attachment or performance
of any operation with this tool other than those recommended in this
instruction manual may present a risk of personalinjury.
19 . Have your tool repaired by a qualifiedperson.
This electric tool complies relevant safety rules. Repairs should only be
carried out by qualified persons using original spare parts; otherwise this
may result in considerable danger to theuser.
Additional Safety Rules for Mitre Saws
• Do not use the saw to cut other materials than those recommended by
themanufacturer.
• Do not operate the machine without guards in position, or if guards do not
function or are not maintainedproperly.
• Ensure that the arm is securely fixed when performing bevelcuts.
• Keep the floor area around the machine level, well-maintained and free of
loose materials, e.g., chips and cut-offs.
• Select the correct blade for the material to becut.
• Use correctly sharpened saw blades. Observe the maximum speed mark on
the sawblade.
• Make sure all locking knobs and clamp handles are tight before starting
anyoperation.
• Never place either hand in the blade area when the saw is connected to
the electrical powersource.
• Never attempt to stop a machine in motion rapidly by jamming a tool or
other means against the blade; serious accidents canoccur.
• Before using any accessory consult the instruction manual.
The improper use of an accessory can causedamage.
• Use a holder or wear gloves when handling a saw blade or roughmaterial.
• Ensure that the saw blade is mounted correctly beforeuse.
• Make sure that the blade rotates in the correctdirection.
• Do not use blades of larger or smaller diameter than recommended. For
the proper blade rating refer to the technical data. Use only the blades
specified in this manual, complying with EN847-1.
• Consider applying specially designed noise-reductionblades.
• Do not use HIGH SPEED STEELblades.
• Do not use cracked or damaged sawblades.
• Do not use any abrasive or diamonddiscs.
• Use only saw blades where the marked speed is at least equal to the speed
marked on thesaw.
• Never use your saw without the kerfplate.
• Raise the blade from the kerf in the workpiece prior to releasing theswitch.
• Before each cut ensure that the machine isstable.
• Do not wedge anything against the fan to hold the motorshaft.
• The blade guard on your saw will open when the guard release lever
2
ispushed.
• Never raise the blade guard manually unless the saw is switched off. The
guard can be raised by hand when installing or removing saw blades or
for inspection of thesaw.
• Check periodically that the motor air slots are clean and free ofchips.
• Replace the kerf plate whenworn.
• Remove the battery from the machine before carrying out any
maintenance work or when changing theblade.
• Never perform any cleaning or maintenance work when the machine is
still running and the head is not in the restposition.
• When fitted with LED, no exchange with different type of LED permitted.
Repairs shall only be carried out by the manufacturer or an authorized
agent.
• Connect the saw to a dust collection device when sawing wood. Always
consider factors which influence exposure of dust suchas:
ʵ type of material to be machined (chip board produces more dust
than wood);