EasyManua.ls Logo

DeWalt DW325PT - User Manual

DeWalt DW325PT
48 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE
USAR EL PRODUCTO.
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-D
e

DW325PT
30° Paper Tape Framing Nailer
Clouese à Charpente de 30° pour ruban de papier
Clavadora Estructural de 30° Para Cinta De Papel
DW325PL
21° Plastic Collated Framing Nailer
Clouese à charpentede 21° en plastique
Clavadora Para Moarcos de 21° Con Unión de Plástico
9R208191_DW325PL_DW325PT_DEWALT, FRAMING NAILER(LPF).indd 1 11/14/14 3:06 PM

Table of Contents

Questions and Answers

  • D
    Donald DavisAug 17, 2025
    What to do if my DeWalt Nail Gun fasteners jam in the tool?
    • J
      Jesse BakerAug 17, 2025
      If fasteners are jamming in your DeWalt nail gun, there are several potential causes. A worn driver channel in the nosepiece can cause jams, so consider replacing the nosepiece. Ensure you are using the recommended size and angle fasteners. A worn driver blade can also lead to jams, so replace the driver blade if necessary. Loose nosepiece screws can also cause fasteners to jam, so tighten them using the appropriate hex wrench.
  • D
    Donald BrownAug 21, 2025
    How to fix air leaks from the top cap of my DeWalt DW325PT?
    • J
      Justin LiAug 21, 2025
      Air leaks from the top cap of your DeWalt Nail Gun can be due to loose cap screws. Tighten the cap screws using an appropriate hex wrench. Alternatively, the gasket or o-ring may be damaged or worn. If so, replace the gasket/o-rings using a Nailer O-Ring Repair Kit.
  • B
    Brian MartinAug 25, 2025
    How to fix exhaust leaks in my DeWalt DW325PT?
    • J
      John MartinAug 25, 2025
      Exhaust leaks in your DeWalt Nail Gun are often due to a damaged main seal or o-ring, or debris. Replace the gasket/o-rings using a Framing Nailer O-Ring Repair Kit in the tool.
  • A
    Amanda RobinsonAug 27, 2025
    Why is my DeWalt Nail Gun lacking power and running sluggishly?
    • L
      Lisa McdonaldAug 27, 2025
      A lack of power or sluggish performance in your DeWalt nail gun can stem from several causes. First, check that the air pressure is adequate. Insufficient lubrication can also cause this issue, so lubricate the tool with DeWalt pneumatic tool oil. Damaged or worn o-rings may be the culprit; if so, replace them using a framing nailer o-ring repair kit. Additionally, a blocked or clogged exhaust port can restrict performance. To resolve this, disconnect the air supply, remove the exhaust plate from the top of the tool, and clean the port. Ensure the depth adjustment isn't set too shallowly, and check the driver for damage or wear, replacing it if necessary.
  • J
    John MatthewsAug 30, 2025
    Why is my DeWalt DW325PT Nail Gun leaking air around the nose when at rest?
    • J
      Jerry MoralesAug 30, 2025
      If your DeWalt Nail Gun leaks air around the nose when it is at rest, it is likely due to damaged or worn o-rings. Replace the gasket/o-rings using a Framing Nailer O-Ring Repair Kit to resolve this issue.
  • S
    Seth BrownSep 3, 2025
    Why is my DeWalt Nail Gun leaking air around the nose when actuated?
    • M
      Mary MendozaSep 3, 2025
      If your DeWalt Nail Gun is leaking air around the nose when in the actuated position, the bumper is likely damaged or worn. Replace the bumper using the Frame Nailer Bumper Kit.
  • J
    jasonwyattSep 6, 2025
    Why does my DeWalt Nail Gun trigger valve housing leak?
    • D
      danielgarzaSep 6, 2025
      A leaking trigger valve housing on your DeWalt Nail Gun is typically caused by an O-ring or valve stem failure. Replace the valve using a Trigger Valve Kit to fix this issue.
  • K
    Karen VazquezSep 9, 2025
    What to do if my DeWalt DW325PT does not cycle in cold weather?
    • S
      Steven LyonsSep 9, 2025
      If your DeWalt Nail Gun does not cycle in cold weather, several factors could be the cause. First, check that the tool is receiving air. If that's not the issue, the valve may be frozen; warm up the tool and lubricate it with DeWalt Pneumatic Tool Oil or a winter weight pneumatic oil containing ethylene glycol. Damaged or worn o-rings can also cause this problem, so replace the gasket/o-rings using a Framing Nailer O-Ring Repair Kit. Lastly, a broken or damaged driver blade could be the culprit, so replace the driver blade if necessary.
  • D
    Dylan ChavezNov 13, 2025
    What to do if my DeWalt DW325PT Nail Gun is skipping nails or has intermittent feed?
    • J
      jillandersonNov 13, 2025
      If your DeWalt Nail Gun is skipping nails or feeding intermittently, several factors could be responsible. First, ensure that the air supply and couplers are not restricted. Insufficient lubrication can also cause this, so lubricate the tool with DeWalt pneumatic tool oil. Check if the nosepiece screws are loose and tighten them if needed. Using the wrong size or angle fasteners can also cause this issue, so use only recommended fasteners. A dirty magazine can impede nail feed, so clean the magazine track and nosepiece. If the magazine is damaged or worn, consider replacing it. A broken or damaged driver blade can also cause this issue, so replace it if necessary. Finally, a worn or damaged trigger valve o-ring or piston o-ring can cause this, so replace the valve using a Trigger Valve Kit...

DeWalt DW325PT Specifications

General IconGeneral
Operating Pressure70 - 120 psi
Air Inlet1/4" NPT
Hose Size3/8"
Nail Size2" - 3-1/4"
Nail Diameter0.113" - 0.131"
Nail Length2" - 3-1/4"
Fastener TypePaper Tape Collated Nails

Related product manuals