DeWalt DW618D User Manual

il Be
sure that the router
bit
is
clear of the
workpiece before
starting the
motor. lf the
bit
is in contact with
the
workpiece
when
the motor
starts
it
could make
the router
jump,
caus-
^
ing damage
or
injury.
IICAUTION:
Wear
appropriate hearing
protectiol,
during use. IJnder
some conditions
and
duration of use, noise from
this
product
may
contribute
to hearing loss.
AWARNTNG:
Some dust created
by
power
sanding, sawing,
grinding,
dritling,
and other
con-
struction activities
contains chemicals known
to cause
cancer,
birlh defects or
other reproduc-
tive harm.
Some examples of these
chemicals are:
.
lead
from lead-based
paint.
.
crystalline silica from
bricks and cement
and
other
masonry
products.
.
arsenic and chromium from
chemicallylreated lumber
(CCA)
Your risk
from these
exposures varies,
depending on how
often
you
do this type
of
work. To
reduce
your
exposure to
these chemicals: work
in a well ventilated
area, and work with
approved
safety equipment, such
as those dust masks
that are
specially designed
to filter out
microscopic
pafticles.
.
Avoid
prolonged
contact with
dust
from
power
sanding,
sawing,
grinding,
drilling,
and
other construction activities.
Wear
protective
clothing
and wash
exposed areas
with soap
and
water.
Allowing
dust to
get
into
your
mouth, eyes,
or lay on the
skin
may
promote
absorption of harmful
chemicals.
AWARNTNG:
tJse
of
this
toot can
generate
and/or
disburse dust, which may
cause
serious
and
permanent
respiratory
or other injury. Always
use NIOSH/OSHA
approved respiratory
pro-
tection appropriate for
the dust exposure. Direct
particles
away from face
and body.
'
The label
on
your
tool may include
the following
symbols. The
symbols and
definitions are
as
follows:
V ............vo\ts
A ............amperes
Hz ..........hert2
W ............watts
min..........minutes
A
..........rufety
atert symbot
FAM'LTAN',ZATTON
Motor
Your DeWALT
tool is
powered
by
a
DEWALT-built
motor.
Be sure
your power
supply agrees
with
the nameplate marking.
"120
V-" means
your
tool may be
operated with alternating
current
only.
Do
not connect
your
tool to a
direct current
power
supply.
All
DTWALT tools
are factory tested;
if this tool
does not
operate, check the
power
supply.
Switch
To
turn the tool
on,
push
the toggle
switch to the
on
position
indicated
on the tool. To
turn the
tool
off,
push
the toggle
switch to the
off
position
indicated
on the tool.
Detachable
Cord Eet
(Fig.
I
J
Insert
the detachable
cordset
plug
so that
the key
(W)
is
aligned with the notch
(V)
in
the
socket.
Turn
the
plug
clockwise
one
quarter
turn
to lock.
A'
CnUnOU:
Always
turn off the toot
and remove the
plug
from the
power
supply
before
detaching the
cordset
from
the tool.
L
CeUnOU: Always leave
the toggle switch in
the off
position
when
removing
or attaching
the cord from
the motor. lf the toggle
switch is in the
on
position
when
the cordset is
attached,
the toolwill
staft
unexpectedly,
causing
loss
of control,
personal
injury
and/or damage to
the
tool
or
workpiece.
FIG, 1
........
alternating
current
-
......direct
current
t1o..........no
load
speed
14) .... . .
Ctass llConstruction
a
..........earthing
terminat
.../min ..revolutions
per
minute

DeWalt DW618D Specifications

General

Brand	DeWalt
Model	DW618D
Category	Network Router
Language	English