DeWalt DW735 - Wood Planing Principles; PLANING BASICS; Proper Planing Technique; TO PLANE YOUR MATERIAL

8
ENGLISH
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
1
Planer
2
Side carrying handles
3
Base handles
4
Bench mounting holes
5
Crank handle
6
On/off switch
Intended Use
This planer is designed for professional woodworking.
DO NOT use under wet conditions or in the presence of
flammable liquids orgases.
This planer is a professional powertool.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
withoutsupervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
Package Contents
The package contains:
1 Planer
1 Round dust port
1 T-wrench (located in the top cover of the unit)
1 Depth adjustment crank handle
1 Hex screw for crank handle
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred duringtransport.
• Take the time to thoroughly read and understand this manual
prior tooperation.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the ratingplate.
Your DeWALT tool is double insulated in accordance
with EN60745; therefore no earth wire isrequired.
If the supply cord is damaged, it must be replaced only by
DeWALT or an authorised serviceorganisation.
• Do not use in dangerous environments. Do not use near
flammable substances, in damp or wet locations, or expose
torain.
• Never plane material which is shorter than 304.8 mm
(12").
• Exhaust chute: remove shavings with brush or vacuum
after power has been shut off and cutter head has
stoppedrotating.
• Always locate planer with proper clearance on the
outfeed side of the unit to prevent pinching or binding
of the workpiece against anyobstacle.
• Clean out your tool often, especially after heavy use.
Dust and grit containing metal particles often accumulate
on interior surfaces and could create a risk of serious injury,
electric shock or electrocution.
• ALWAYS WEAR SAFETYGLASSES.

WARNING: For your own safety, it is recommended
that two people carry this machine or serious injury
couldresult.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewellery or long hair can be caught
in movingparts.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA orless.

WARNING: Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-
treatedlumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed
to filter out microscopicparticles.
• Avoid prolonged contact with dust from power sanding,
sawing, grinding, drilling, and other construction activities.
Wear protective clothing and wash exposed areas with soap
and water. Allowing dust to get into your mouth, eyes, or lay
on the skin may promote absorption of harmful chemicals.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the oldplug.
• Connect the brown lead to the live terminal in theplug.
• Connect the blue lead to the neutralterminal.

WARNING: No connection is to be made to the
earthterminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm
2
; the
maximum length is 30m.
When using a cable reel, always unwind the cablecompletely.