DeWalt DWE4233 - Accessories and Attachments; Accessory and Guard Selection; Mounting Guards and Discs

45
english
3. Keeping the guard release lever open, push the
guard down until the lugs engage then rotate
them into the groove on the gear case hub.
Release the guard releaselever.
4. With the spindle facing the operator, rotate
the guard clockwise into the desired working
position. The guard body should be positioned
between the spindle and the operator to
provide maximum operatorprotection.
5. For easy adjustment, the guard can be rotated
in the clockwise direction. The guards design
allows the guard to be rotated and adjusted
by turning the guard in a clockwise, single
action motion. The lever does not need to
be depressed to turn the guard. The lever is
only used for removal of the guard. The guard
can be repositioned the opposite direction by
depressing the guard release lever. NOTE: The
guard release lever should snap into one of the
alignment holes(O) on the guard collar. This
ensures that the guard is secure.
6. To remove the guard, follow steps 1–3 of these
instructions inreverse.
Fitting and Removing a Grinding or
Cutting Disc (fig. 1, 4, 5)
WARNING: Do not use a damageddisc.
1. Place the tool on a table, guard (F)up.
2. Fit the backing flange(D) correctly onto the
spindle(B) (fig. 4).
3. Place the disc(P) on the backing flange(D).
When fitting a disc with a raised centre, make
sure that the raised centre(Q) is facing the
backing flange(D).
4. Screw the threaded locking flange(E) onto the
spindle(B) (fig. 5):
a. The ring on the threaded locking flange(E)
must face towards the disc when fitting a
grinding disc (fig. 5A);
b. The ring on the threaded locking flange(E)
must face away from the disc when fitting a
cutting disc (fig. 5B).
5. Press the spindle lock button(A) and rotate the
spindle(B) until it locks inposition.
6. Tighten the threaded locking flange(E) with the
hex key (S) provided or a two pinspanner.
7. Release the spindlelock.
8. To remove the disc, loosen the threaded locking
flange(E) with the hex key (S) provided or a two
pinspanner.
Accessories and Attachments
It is important to choose the correct guards,
backing pads and flanges to use with grinder
accessories. Refer to chart at the end of this section
for information on choosing the correctaccessories.
NOTE: Edge grinding can be performed with
Type27 wheels designed and specified for
thispurpose.
WARNING: Accessories must be rated
for at least the speed recom mended on
the tool warning label. Wheels and other
accessories running over rated accessory
speed may burst and cause injury.
Threaded accessories must have a M14
hub. Every unthreaded accessory must
have a 22 mm arbor hole. If it does not,
it may have been designed for a circular
saw and should not be used. Use only
the accessories shown in the chart at the
end of this section. Accessory ratings
must be above listed minimum wheel
speed as shown on toolnameplate.
Mounting Guards
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
WARNING: Guards must be used with
this grinder.
When using the DWE4233 or the DWE4237 grinder
for cutting metal or masonry, a Type 1 guard MUST
be used. Type1 guards are available at extra cost
from
DeWALT
distributors.
NOTE: Please refer to the Grinding and Cutting
Accessory Chart at the end of this section to
see other accessories that can be used with
thesegrinders.
MOUNTING AND REMOVING ONE-TOUCH GUARD (FIG. 3)
NOTE: If your grinder is supplied with a keyless
One-Touch guard, ensure the screw, lever,
and spring are fitted correctly before mounting
theguard.
1. Press the guard release lever(J).
2. While holding the guard release lever open,
align the lugs(M) on the guard with the slots (N)
on the gearcase.