DeWalt DWE46125 - Operation and Adjustments; Depth of Cut Adjustment; Dust Extraction System; Guiding Wheels

ENGLISH
7
Flange / Grinder Compatibility Chart
Flange set Grinder
Long (black)
flange set:
Locking flange
13
Backing flange
14
DWE43214, DWE43214N,
DWE43214NVS, DWE43240INOX,
DWE43231VS, DWE43244N,
DWE43240VS, DWE46253,
DWE46202, DWE43265N,
DWE43840CN
DWE43113, DWE43115, DWE43115N,
DWE43066, DWE43066N,
DWE43116, DWE43116N, DWE43114,
DWE43114N, DWE43131, DWE43144,
DWE43144N, DWE43140, DWE46103,
DWE46153, DWE46155
DWE402G, DWE402K, DWE402,
DWE402N
DWE4222, DWE4222N, DWE4214
DCG414
DWE4020, DWE4120, DWE4011
Depth of Cut Adjustment (Fig.A)
1. Loosen the depth of cut adjustment knob
5
.
2. Slide the depth of cut adjustor
4
to the
desiredposition.
NOTE: If the shroud is closed, press the front shroud
button
7
to open the shroud. This will make it easier to
move the depth of cutadjustor.
3. Tighten the depth of cut adjustmentknob.
Dust Extraction (Fig.A,G)

WARNING: Use only power tools and dust extractors
recommended by D
e
WALT with thisattachment.
For more information about D
e
WALT power tools
compatible with this attachment, please contact your local
dealer, call 1–800–4-D
e
WALT (1–800–433–9258) or visit our
website www.
DeWALT
.com.

WARNING: This attachment must be used with a dust
extractor system. ALWAYS wear certified safety face
or dustmask.
NOTE: Ensure hose connection issecure.
NOTE: The amount of dust retained by the dust extractor
vacuum is dependent on its filter system. Refer to the dust
extractor vacuum instruction manual for moreinformation.
All D
e
WALT dust collection shrouds are designed to work
with the D
e
WALT Air lock™ universal DWV9000connector.
1. Attach the DWV9000 connector
22
to your dust
collector hose
23
.
2. Unlock the DWV9000 connector and slide onto
dust port
1
.
3. Lock the DWV9000 connector tosecure.
Fig. G
23
22
1
Traditional Dust Extractor Vacuum
Hoses
Attach recommended dust extractor vacuum hose to
dust port
1
.
Removing and Attaching Guiding Wheels
(Fig. H)

WARNING: The cutting shroud should only be
used either (1) when all four wheels are attached
and in good working condition or (2) when all four
wheels are removed and the metal base is in good
workingcondition.
This cutting shroud comes with four removable guiding
wheels
6
on the metal base
3
which can be detached if
notneeded.
1. Remove the clips
26
holding the wheels to thebase.
2. Remove the guidingwheels.
3. Remove the pivot pin
27
.
To attach the guiding wheels to the base, reinsert the pivot
pin, slide the wheels on their axles and secure the clips
in place. Make sure all four guiding wheels are securely
attached before using the cuttingshroud.
Fig. H
26
63
27
6
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can causeinjury.