DeWalt DWE575-CA - Page 12

ENGLISH
12
Repairs

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including power
cord repairs and brush inspection and replacement) should
be performed by a DeWALT factory service center or a
Assembling the Dust Port (Fig. S)
1. Align the dust port
23
over upper blade guard
12
asshown.
2. Insert two dust port screws
24
as shown and
tightensecurely.
Dust Extraction

WARNING: Risk of dust inhalation. To reduce the risk of
personal injury, ALWAYS wear an approved dustmask.

WARNING: ALWAYS use a vacuum extractor designed
in compliance with the applicable directives regarding
dust emission when sawing wood. Vacuum hoses of most
common vacuum cleaners will fit directly into the dust
extractionoutlet.
A dust extraction port is available at extra cost from your
local dealer or authorized servicecenter.
Accessories

WARNING: Since accessories, other than those offered by
DeWALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the
risk of injury, only DeWALT recommended accessories should
be used with thisproduct.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact DeWALT call 1-800-4-DeWALT
(1-800-433-9258) or visit our website: www.dewalt.com.
Brushes (Fig.R)

WARNING: To reduce the risk of injury, turn unit off
and disconnect it from power source before installing and
removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
Inspect carbon brushes regularly by disconnecting the
tool from the power source, removing the four end cap
screws
20
with a screwdriver, then removing the end cap
4
.
Keep brushes clean and sliding freely in their guides.
Always replace a used brush in the same orientation in
the holder as it was prior to removal. Carbon brushes have
varying symbols stamped into their sides, and if either
brush is worn down to the line closest to the spring, take
the tool to a DeWALT authorized service center for brush
assembly replacement. Use only identical DeWALT brushes.
Always replace the end cap after inspecting or servicing
brushes. The tool should be allowed to “run in” (run at
no load without a blade) for 5 minutes before use to seat
newbrushes.
While “running in” DO NOT TIE, TAPE, OR OTHERWISE LOCK
THE TRIGGER SWITCH ON. HOLD BY HAND ONLY.
Occasionally, the brake will not function properly and
won’t stop the saw in the 2 seconds discussed above. If this
condition persists, turn the saw on and off four or five times.
If the brake still does not stop the blade in about 2 seconds,
the problem may be worn brushes. Have the brushes
replaced at a DeWALT authorized service center.
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with yourproduct.
• CONFIRMATION OF OWNERSHIP: In case of an
insurance loss, such as fire, flood or theft, your registration of
ownership will serve as your proof ofpurchase.
• FOR YOUR SAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification is
required under the Federal Consumer SafetyAct.
• Register online at www.dewalt.com.
Three-Year Limited Warranty
For warranty terms, go to https://www.dewalt.com/
support/warranty.
To request a written copy of the warranty terms, contact:
Customer Service at DeWALT Industrial Tool Co., 701East
Joppa Road, Towson, MD 21286or call 1-800-4-DeWALT
(1-800-433-9258).
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warrantyinformation.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-800-4-DeWALT
(1-800-433-9258) for a freereplacement.
DeWALT authorized service center. Always use identical
replacementparts.
Refer to Brushes for brush replacement information.