DeWalt DWE8100T - Page 19

17
한국어
8
한국어
주의: 와이어 브러시 및 휠을 취급할 때는 작업용
장갑을 착용하십시오. 날카롭게 될 수 있습니다.
주의: 휠 또는 브러시 장착 시 또는 사용 중에
가드에 닿아서는 안됩니다. 액세서리에 감지할 수
없는 손상이 발생할 수 있고, 와이어가 액세서리 휠
또는 컵에서 부서질 수 있도록 합니다.
1. 손으로 휠을 스핀들에 끼웁니다.
2. 스핀들 잠금 버튼을 누르고 와이어 휠 또는 브러시 허브에 있는
렌치를 사용하여 휠을 조입니다.
3. 휠을 제거하려면 위의 절차와 반대로 하십시오.
참고: 공구를 켜기 전에 휠 허브를 제대로 끼우지 못하면 공구 또는
휠이 손상될 수 있습니다.
공구에 대한 와이어 브러시 및 와이어 휠의 권장 직경은 100mm
(DWE8100S, DWE8100T) 또는 125mm (DWE8110S) 입니다.
이면 패드/샌딩 시트 장착 및 분리
1. 가드가 위를 향하도록 테이블 또는 평면에 공구를 올려 놓습니다.
2. 아래 만조 (d) 를 분리합니다.
3. 스핀들 (b) 에 고무 이면 패드를 정확하게 놓습니다.
4. 고무 이면 패드에 사포를 놓습니다.
5. 덮개 만조 (e) 를 스핀들에 나사로 고정합니다. 덮개 만조의 링은
고무 이면 패드 쪽을 향해야 합니다.
6. 스핀들 잠금 버튼 (a) 을 누르고 제자리에 잠길 때까지 스핀들 (b)
을 돌립니다.
7. 제공된 육각 키 또는 두 개의 핀 스패너를 사용하여 덮개 만조 (e)
를 조입니다.
8. 스핀들 잠금을 놓습니다.
9. 고무 이면 패드를 제거하려면, 제공된 렌치 또는 육각 키 또는 두
개의 핀 스패너를 사용하여 덮개 만조 (e) 를 풉니다.
공구의 경우 이면 패드/사포의 권장 직경은 100mm (DWE8100S,
DWE8100T) 또는 125mm (DWE8110S) 입니다.
와이어 컵 브러시 장착
스페이서 및 나사산 플랜지를 사용하지 않고 와이어 컵 브러시를
스핀들에 직접 고정합니다.
100mm 그라인딩 휠
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
27형 가드
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
백킹 플랜지
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
27형 오프셋 그라인딩 휠
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
클램프 너트
와이어 휠
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
27형 가드 27형 가드
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
75mm 와이어 컵 브러시 100mm 와이어 휠
100mm 휠
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
1형 가드 1형 가드
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
백킹 플랜지 백킹 플랜지
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
얇은 회전판 다이아몬드 휠
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
클램프 너트 클램프 너트
100mm 샌딩 플랩 디스크
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
27형 가드
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
백킹 플랜지
English
11
Prior to Operation
 • Installtheguardandappropriatediscorwheel.
Do not use excessively worn discs or wheels.
 • Besuretheinnerandouterflangesare
mounted correctly.
 • Makesurethediscorwheelrotatesinthe
direction of the arrows on the accessory and
the tool.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
WARNING:
 •Ensureallmaterialstobegroundor
cut are secured in place.
 •Secureandsupporttheworkpiece.
Use clamps or a vice to hold and
support the workpiece to a stable
platform. It is important to clamp and
support the workpiece securely to
prevent movement of the workpiece
and loss of control. Movement of
the workpiece or loss of control may
create a hazard and cause personal
injury.
 •Applyonlyagentlepressuretothe
tool. Do not exert side pressure on the
disc.
 •Avoidoverloading.Shouldthetool
become hot, let it run a few minutes
under no load condition.
Proper Hand Position (fig. 6)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (figure 1), with the other hand on the body of
the tool, as shown in figure 6.
Switches
CAUTION: Hold the body of the tool
firmly to maintain control of the tool at
start up and during use and until the
wheel or accessory stops rotating. Make
sure the wheel has come to a complete
stop be fore laying the tool down.
NOTE: To reduce unexpected tool movement,
do not switch the tool on or off while under load
conditions. Allow the grinder to run up to full speed
before touching the work surface. Lift the tool from
the surface before turning the tool off. Allow the tool
to stop rotating before putting it down.
SLIDER SWITCH DWE8100S & DWE8110S (FIG. 3)
WARNING: Before connecting the tool
to a power supply, be sure the slider
switch is in the off position by pressing
the rear part of the switch and releasing.
Ensure the slider switch is in the off
position as described above after any
interruption in power supply to the tool,
such as the activation of a ground fault
interrupter, throwing of a circuit breaker,
accidental unplugging, or power failure.
If the slider switch is locked on when the
power is connected, the tool will start
unexpectedly.
To start the tool, slide the slider switch (g) toward the
front of the tool. To stop the tool, release the slider
switch.
For continuous operation, slide the switch toward
the front of the tool and press the forward part of
the switch inward. To stop the tool while operating
100mm Sanding Flap Discs
backing flange
non-hubbed sanding
flap disc
clamp nut
Type 27 guard
비허브 샌딩 플랩 디스크
English
10
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the above
procedure.
NOTICE: Failure to properly seat the wheel hub
before turning the tool on may result in damage to
tool or wheel.
The recommended diameter of Wire Brushes
andWire Wheels for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting and Removing a
Backing pad/Sanding sheet
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (d).
3. Place the rubber backing pad correctly onto the
spindle (b).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (e) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
7. Tighten the threaded clamp nut (e) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (e) with the hex key
provided or a two pin spanner.
The recommended diameter of backing pad/
sanding sheet for the tool is 100mm(DWE8100S,
DWE8100T) or 125mm(DWE8110S) .
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
100mm Grinding Wheels
Wire Wheels
100mm Cutting Wheels
Type 27 guard
Type 27 guard
75mm wire cup bruch 100mm wire cup bruch
Type 27 guard
backing flange
clamp nut
Type 27 depressed
center wheel
Type 1 guard
backing flange
abrasive cutting wheel
clamp nut
Type 1 guard
backing flange
diamond cutting wheel
clamp nut
클램프 너트