DeWalt DWOAS9ST - Accessories; Reloading the Cutting Line; Adjusting the String Cutting Blade

9
ENGLISH
Adjusting the String Cutting Blade (Fig.K)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories, when
replacing line, or prior to cleaning. An accidental
start‑up can causeinjury.

WARNING: Do not operate the trimmer without a
cutting blade installed.
The cutting swath of this string trimmer is adjustable to 15"
or 17" (381 mm or 432 mm).
1. With a screwdriver, removethe two screws
14
that
secure the cutting blade
15
onto the guard
2
.
2. Position the loose cutting blade
15
at the desired cutter
slot (15"
17
or 17"
16
(381 mm or 432 mm)) as shown
in Fig. K.
3. With a screwdriver, installthe two screws
14
to secure
the cutting blade
15
onto the guard
2
.
Reloading the Cutting Line (Fig.I, J)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories, when
replacing line, or prior to cleaning. An accidental
start‑up can causeinjury.

CAUTION: Use only DeWALT replacement spools
and line. Using any other manufacturer's line can
reduce performance, damage the trimmer or cause
personalinjury.
Your trimmer uses 0.08" (2.0mm) diameter line that
is spiral‑shaped with smooth round edges. Do not use
other size lines. This can degrade performance, cause
damage to the unit orinjury.

CAUTION: To avoid appliance damage, if the cutting
line protrudes beyond the trimming blade, cut it off so
that it just reaches theblade.
Use only
DeWALT replacementline.
1. Removebattery.
2. Cut a max of 20' (6 m) length of of 0.08" (2.0 mm)
trimmerline.
3. Align spool housing eyelets
22
with the arrow
23
on
the spool grip cover
19
as shown in FigureI.
4. Thread one end of the trimmer line through an eyelet.
Guide the line through to the second eyelet and continue
to pull the line through until there are equal lengths of
string on each side of the spoolhousing.
5. Secure the spool cap from moving with one hand. Using
your other hand, wind the string onto the spool by
rotating the spool grip cover counterclockwise. Continue
winding until 5" (130mm) of string remain on each side
of the spoolhousing as shown in Fig.J.
Replacing Spool Assembly (Fig.H)
1. Rotate the spool housing
3
until the hole
24
in the
spindle plate aligns with notch
18
in the motor housing.
Insert a screwdriver through the notch and into the hole,
to prevent the spindle fromturning.
2. Unscrew and remove the spool housing by turning the
spool grip cover
19
clockwise.
NOTE: Do not try to remove the spool housing by
turning the spool housing
3
.
3. Remove spindle plate
20
before installing a new spool.
Remove any dirt and grass from the motor housing and
spindleplate.
4. Install spindle plate
20
onto the spindle
21
, so the
double D shaped retaining nut on the spindle sits inside
the base of the spindleplate.
5. Align the spindle plate hole and notch, insert the
screwdriver back into the hole and thread the new spool
housing counterclockwise. Securely tighten the new
spool housing onto the spindle
21
.

WARNING: To reduce the risk of serious personal
injury, turn appliance off and remove battery
before making any adjustments or removing/
installing attachments oraccessories.

WARNING: The use of any accessory not
recommended by DeWALT for use with this appliance
could behazardous.

WARNING: Do not use any blades, or any accessory
or attachment other than those recommended by
DeWALT on this trimmer. Serious injury or product
damage mayresult.

CAUTION: Use only DeWALT replacement spools
and line All line must be spiral‑shaped with smooth,
roundedges. Using any other manufacturer's line can
reduce performance, damage the trimmer or cause
personalinjury.
Your trimmer uses 0.08" (2.0mm) diameter line, however a
0.095" (2.4mm) line may beused. Other sizes may degrade
performance or cause damage to thetrimmer. Other sizes
may degrade performance or cause damage to thetrimmer.
Accessories

WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact
DeWALT call 1-800-4-DeWALT (1-800-433-9258) or
visit our website: www.dewalt.com.