DeWalt DWOAS9ST - Operation; Proper Hand Position; Trimming; Additional Safety Instructions for Grass Trimmers

ENGLISH
6
ADDITIONAL SAFETY INSTRUCTIONS FOR
GRASS TRIMMERS

WARNING: Cutting elements continue to rotate after
the motor is switchedoff.
• Wear long pants to protect yourlegs from flying debris.
• Wear appropriate footwear to protect your feet from debris,
including flying debris.
• Before using the appliance, check that your cutting path is
free from sticks, stones, wire and any otherobstacles.
• To reduce the risk of rebound (ricochet) injury, work going
away from any nearby solid object such as a wall, steps,
large stone, tree, etc. Use great care when working close to
solid objects and where necessary, do trimming by hand.
• Only use the appliance in the upright position, with the
cutting line near the ground. Never switch the appliance on
in any otherposition.
• Move slowly when using the appliance. Be aware that
freshly cut grass is damp andslippery.
• Do not work on steep slopes. Work across the face of slopes,
not up anddown.
• Do not overreach. Keep proper footing and balance at all times.
• Never cross gravel paths or roads while the appliance
isrunning.
• Avoid accidental starting. Do not carry with your finger on
the trigger when the battery is installed.
• Never touch the cutting line while the appliance isrunning.
• Do not put the appliance down until the cutting line has
come to a completestandstill.
• Use only the appropriate type of cutting line. Never use
metal cutting line, metal wire, cable, rope or fishingline.
• Keep face, hands and feet away from the cutting line and
blade at all times, especially when switching on themotor.
• Before using the appliance and after any impact, check for
signs of wear or damage and repair asnecessary.
• If you strike or become entangled with an object, stop the
appliance immediately. Remove battery, check for damage
and have any damage repaired before continuing. Do not
operate with a broken hub or spool.
• Take care against injury from any device fitted for trimming
the filament line length. After extending new cutter line
always return the machine to its normal operating position
before switchingon.
• Close supervision is necessary when the appliance is used
nearchildren.
• This appliance is not intended for use by young or infirm
persons withoutsupervision.
• This appliance is not to be used as atoy.
• Use in a dry location only. Do not allow the appliance to
becomewet.
• Do not immerse the appliance inwater.
• Do not open the body casing. There are not user‑serviceable
parts inside
• Do not operate the appliance in explosive atmospheres,
such as in the presence of flammable liquids, gases ordust.
b ) Never allow children or people unfamiliar with
these instructions to use the machine. Local
regulations can restrict the age of theoperator.
c ) Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or
theirproperty.
Preparation
a ) Before use, always visually inspect the machine for
damaged, missing or misplaced guards orshields.
b ) Never operate the machine while people, especially
children, or pets arenearby.
Operation
a ) Wear eye protection and stout shoes at all times while
operating themachine.
b ) Avoid using the machine in bad weather conditions
especially when there is a risk oflightning.
c ) Use the machine only in daylight or good artificiallight.
d ) Never operate the machine with damaged guards or
shields or without guards or shields inplace.
e ) Switch on the motor only when the hands and feet are
away from the cuttingmeans.
f ) Always disconnect the machine from the power supply
(i.e.remove the plug from the mains, remove the
disabling device or removable battery)
• whenever the machine is left unattended;
• before clearing a blockage;
• before checking, cleaning or working on the
machine;
• after striking a foreign object;
• whenever the machine starts vibratingabnormally.
g ) Take care against injury to feet and hands from the
cuttingmeans.
h ) Always ensure that the ventilation openings are kept
clear ofdebris.
i ) Remove any objects that may cause kickback, such as
branches androcks.
j ) Check for loose fasteners and damagedparts.
k ) Hold the tool using only the designated gripping
surfaces: the powerhead housing and the auxiliary
handle (see Fig.D).Do not use the pole as a
grippingsurface.
Maintenance and Storage
a ) Disconnect the machine from the power supply
(i.e.remove the plug from the mains, remove the
disabling device or removable battery) before carrying
out maintenance or cleaningwork.
b ) Use only the manufacturer’s recommended
replacement parts andaccessories.
c ) Inspect and maintain the machine regularly.Have
the machine repaired only by an authorizedrepairer.
d ) When not in use, store the machine out of the reach
ofchildren.
e ) Clean before storing, including the use of guards.