DeWalt DWST08050 - USB Charging Ports; Cleaning; Accessories; Tool Connect Chip

ENGLISH
10
Repairs
The charger and batteries are notserviceable. There are no
serviceable parts inside the charger or batterypack.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including power
cord repairs, and brush inspection and replacement,
when applicable) should be performed by a
DeWALT
factory service center or a DeWALT authorized service
center. Always use identical replacementparts.
Tool Connect™ Chip (Fig.H, I)
Optional Accessory
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ chip
21
communicates with an optional
application for your smart device (such as a smart phone
or tablet) that connects the device to utilize the mobile
application for inventory management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
moreinformation.
Installing the Tool Connect™ Chip
1. Insert the Tool Connect™ Chip 
21
into the
emptypocket
23
.
2. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws
22
and
tighten thescrews.
3. Refer to Tool Connect™ Chip Instruction Sheet for
furtherinstructions.
Accessories

WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this product could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact
DeWALT call 1-800-4-DeWALT
(1-800-433-9258) or visit our website: www.dewalt.com
Cleaning

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source and remove the battery pack before making
any adjustments or removing/installing attachments
or accessories. An accidental start‑up can causeinjury.
Your DeWALT product has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
care and regularcleaning.
USB Charging Ports (Fig.A, G)
The DWST08050 is equipped with one USB
17
and one
USB-C
18
charging ports. The USB
17
delivers up to
2.0amps and the USB-C
18
delivers up to 3.0amps of
totalcurrent.
NOTE: The current delivered to the device is dependent
upon the user's device and user's chosen cable.
NOTE: Do not plug in devices that exceed the output ratings
on the DWST08050 rating label. Doing so will shorten the
charger's usefullife.
Using the USB port:
1. Open the storage door to gain access to the USB
charging port
17
.
2. Insert a USB plug into USB charging port
17
to supply
power or charge yourdevice.
Using the USB-C port:
1. The USB-C charging port
18
is located on the back of
the box, above the power cord
8
.
2. Pull back the USB-C port cover
7
to reveal the USB-C
charging port
18
.
3. Insert a USB-C plug into USB-C charging port
18
to
supply power or charge yourdevice.
NOTE: Ensure the port cover is reinstalled after use.
Storage and Transportation
• Always store disconnected from power supply!
• Avoid using the product outdoors or transporting in an
open vehicle if there is noticeable damage to the sealing
gasket or plastic exterior.
• Avoid continuous exposure to rain or other precipitation
if stored outdoors or on a vehicle, or if transported in an
openvehicle.
• Store the charger in a place that is as cool and dry
aspossible.
• Store the charger in a place where it cannot be accessed by
children or unauthorizedpersons.
• Check the charger for damage before use after long periods
ofstorage.