DeWalt DXV30SAPTA User Manual

9
SHUT DOWN/TRANSPORTATION (Fig. A)
1. Turn on/o switch
3
to the OFF position.
2. Unplug the unit.
3. Store the power cord
2
wrapping it around the top
handle/cord wrap
1
as shown.
4. When transporting in vehicles, secure the
machine.
MAINTENANCE
The DEWALT appliance has been designed to
operate overall long period of time with a minimum
of maintenance.Continuous satisfactory operation
depends upon proper appliance care and regular
cleaning.
WARNING: To reduce the risk of injury, turn
appliance o and disconnect appliance from
power source before installing and removing
accessories, before adjusting or changing set-
ups or when making repairs. An accidental start-up
can cause injury.
WARNING: For user servicing, the machine must
be dismantled, cleaned and serviced, as far as is
reasonably practicable, without causing risk to the
maintenance sta and others. Suitable precautions
include, decontamination before dismantling,
provision for local ltered exhaust ventilation
where the machine is dismantled, cleaning of the
maintenance area and suitable personal protection.
• The manufacturer, or an instructed person, shall
perform a technical inspection at least annually,
consisting of, for example, inspection of the lter for
damage, air tightness of the machine and proper
function of the control mechanism.
• When carrying out service or repair operations, all
contaminated items which cannot be satisfactorily
cleaned, are to be disposed of; such items shall
be disposed of in impervious bags in accordance
with any current regulation for the disposal of such
waste.
• For dust extractors it is necessary to provide for
an adequate air change rate L in the room if the
exhaust air is returned to the room.
NOTE: Refer to national regulations is necessary.
FILTER (Fig. A, H, I)
FILTER CARE
The lters included with this vacuum are long life
lters. To be eective in minimizing dust recirculation,
the lters MUST be installed correctly and in good
condition.
WARNING: Appropriate personal protective
equipment like dust mask and gloves should be used
while handling the lters.
TO REMOVE FILTERS
1. Turn on/o switch
3
to the OFF position ( O ) and
unplug cord from outlet.
2. Release lid latches
5
és vegye le a and remove
vacuum head
4
from canister. Place vacuum
head on a level surface upside down.
3. Turn each lter
9
counterclockwise by gripping it
on the plastic end cover as shown, and carefully
remove from head, ensuring debris does not fall
into mounting hole.
NOTE: Use care to not damage lter material.
4. If the bottom side of the vacuum head needs to
be cleaned, use a cloth dampened with water and
mild soap and allow it to dry. Dispose the cloth in
an appropriate container.
5. Inspect lters for wear, tears or other damage.
NOTE: If there is any doubt on the condition of the
lters they MUST be replaced. DO NOT continue
use if lters are damaged.
WARNING: Never use compressed air or a
brush to clean lters, otherwise damage to the lter
membrane will occur which will allow dust to pass
through the lter.
If needed, gently tap against a hard surface or rinse
with room temperature water and let air dry. Cleaning
of the lters is typically unnecessary, even if the lter is
covered with dust. The automatic lter cleaning system
will maintain maximum performance and continue
to function. If visual damage to the lter membrane
exists, replace lters. Filters typically last between six
and twelve months depending on use and care.
TO INSTALL FILTERS
1. Ensure lter seal
15
is in place and is secure.
2. Line up lter threads
16
to vacuum head threads
and using moderate force, turn lter clockwise until
tight.
NOTE: Use careful to not damage lter material.
3. Place the vacuum head
4
onto the dust tank and
secure it by closing the lid latches
5
.
TO EMPTY DUST TANK (Fig. J)
WARNING: To reduce the risk of injury from
accidental starting, unplug power cord before
emptying the dust tank.
1. Remove the power head assembly of the wet/
dry vac bypulling outward on the lid clips located
on each side of the vac. Lift o the power head
assembly.
2. Dump the tank contents into the proper waste
disposal container.
BLOWING OPERATION
WARNING: To avoid injury to bystanders, keep
them clear of blowing debris.
CAUTION! Wear a dust mask if blowing creates
dust which might be inhaled.
CAUTION! To reduce the risk of hearing loss,
wear ear protectors when using the vac/blower for
extended hours or when using it in a noisy area.
CONNECTING POWER TOOL (Fig. K, L)
1. Make sure on/o switch
3
is in the ‘O’position
and the power supply is not connected.
2. There are 2 options for the next step. then connect
the power supply and turn on/o switch
3
to the ON
position ( I ), at this time the vacuum cleaner will start
working. Then connect the power supply and turn on/
o switch
3
to the ON position ( I I ), at this time the
power tool can start to use.
EN

DeWalt DXV30SAPTA Specifications

General

Brand	DeWalt
Model	DXV30SAPTA
Category	Vacuum Cleaner
Language	English