DeWalt XR DCF850 Original Instructions

ENGLISH
16
English (original instructions)
BRUSHLESS CORDLESS COMPACT IMPACT DRIVER
DCF850
DCF850
Voltage V
DC
18
Type 1/10/20
Battery type Li-Ion
Power output W 475
No load speed rpm
Mode 1 0–1000
Mode 2 0–2800
Mode 3 0–3250
Impact rate ipm 0–3800
Max torque Nm 206.2
Tool holder mm 6.35
Weight (without battery pack) kg 0.95
Noise values and vibration values (triax vector sum) according to EN62841-2-2:
L
PA
(emission sound pressure level)
dB(A) 88
L
WA
(sound power level)
dB(A) 99
K (uncertainty for the given sound level)
dB(A) 3
Vibration emission value a
h
= m/s
2
18.5
Uncertainty K = m/s
2
1.7
The vibration and/or noise emission level given in this
information sheet has been measured in accordance with
a standardised test given in EN62841 and may be used to
compare one tool with another. It may be used for a preliminary
assessment ofexposure.

WARNING: The declared vibration and/or noise emission
level represents impact tightening of fasteners of the maximum
capapcity of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the
vibration and/or noise emission may differ. This may significantly
increase the exposure level over the total workingperiod.
An estimation of the level of exposure to vibration and/or
noise should also take into account the times when the tool is
switched off or when it is running but not actually doing the job.
This may significantly reduce the exposure level over the total
workingperiod.
Identify additional safety measures to protect the operator from
the effects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm (relevant for vibration),
organisation of workpatterns.
EC-Declaration of Conformity
Machinery Directive
Brushless Cordless Compact Impact Driver
DCF850
DeWALT declares that these products described under
Technical Data are in compliance with:
2006/42/EC, EN62841-1:2015, EN62841-2-2:2014.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact DeWALT at
the following address or refer to the back of themanual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf ofDeWALT.
Markus Rompel
Vice President of Engineering, PTE-Europe
DeWALT, Richard-Klinger-Straße 11,
65510, Idstein, Germany
07.04.2021
DECLARATION OF CONFORMITY
THE SUPPLY OF MACHINERY (SAFETY) REGULATIONS
2008
Brushless Cordless Compact Impact Driver
DCF850
DeWALT declares that these products described under
“technical data” are in compliance with:
EN62841-1:2015, EN62841-2-2:2014
These products conform to the following UK Regulations
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (as amended).
Electromagnetic Compatibility Regulations, 2016, S.I.2016/1091
(as amended).
The Restriction of the Use of Certain Hazardous Substances
in Electrical and Electronic Equipment Regulations 2012, S.I.
2012/3032 (as amended).
For more information, please contact DeWALT at the following
address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of DeWALT.
WARNING: Read all safety warnings, instructions,
illustrations, and specifications in this manual,
including the battery and charger sections provided in
an original tool manual or the separate Batteries and
Chargers manual. Manuals can be obtained by contacting
Customer Service (refer to the back page of thismanual).
Technical Data

DeWalt XR DCF850 Specifications

General

Voltage	18V
Impacts per Minute	0-3800 IPM
LED Light	Yes
Anvil Type	1/4-inch hex
Battery Type	Li-Ion
Max Torque	205 Nm