Diamondback 57087 - User Manual

Questions and Answers

A
Amanda HarrisAug 4, 2025
What to do if my Diamondback 57087 Saw will not start?
- C
  cpalmerAug 4, 2025
  If your Diamondback Saw won't start, there are several potential causes: 1. The cord may not be properly connected. Ensure the cord is securely plugged in. 2. There may be no power at the outlet. Check the power at the outlet. If the outlet is unpowered, turn off the saw and check the circuit breaker. If the breaker is tripped, ensure the circuit has the correct capacity for the saw and isn't overloaded with other devices. 3. The tool’s thermal reset breaker may have tripped (if your model has one). Turn off the saw and allow it to cool, then press the reset button on the tool. 4. There could be internal damage or wear to components like carbon brushes or the switch. In this case, have a qualified technician service the saw.
K
Kimberly NguyenAug 11, 2025
Why is my Diamondback Saw overheating?
- S
  Scott WernerAug 11, 2025
  Several factors can cause a Diamondback Saw to overheat: 1. Forcing the machine to work too fast. Allow the machine to work at its own pace. 2. Misaligned accessory. Check and correct the alignment of the accessory to the fence and/or table. 3. Worn or damaged blade. Replace worn blades as needed. 4. Blocked motor housing vents. Wear ANSI-approved safety goggles and a NIOSH-approved dust mask/respirator while blowing dust out of the motor using compressed air. 5. Motor strained by a long or small diameter extension cord. Eliminate the use of an extension cord. If an extension cord is necessary, use one with the proper diameter for its length and load.
B
brittany85Aug 17, 2025
What to do if the performance of my Diamondback Saw decreases over time?
- J
  Jeffrey BernardAug 17, 2025
  If you notice the performance of your Diamondback Saw decreasing over time, it could be due to: 1. A worn or damaged blade. Replace worn blades as needed. 2. Worn or damaged carbon brushes. Have a qualified technician replace the brushes.
M
Mary HaleAug 23, 2025
Why does my Diamondback 57087 operate slowly?
- L
  Lindsay JonesAug 23, 2025
  If your Diamondback Saw is operating slowly, it may be due to an extension cord that is too long or has a wire size that is too small. Try eliminating the use of the extension cord. If an extension cord is needed, use one with the proper diameter for its length and load.
M
mitchelljohnAug 29, 2025
What to do if my Diamondback 57087 makes excessive noise or rattling?
- H
  Herbert HarrisAug 29, 2025
  Excessive noise or rattling in your Diamondback Saw can be caused by internal damage or wear to components such as carbon brushes or bearings. Have a technician service the tool.

Summary

Safety Information

Warning Symbols and Definitions

Explains the meaning of hazard alert symbols like DANGER, WARNING, CAUTION, and NOTICE.

General Tool Safety Warnings

Provides fundamental safety rules applicable to all power tools.

Grounding Instructions

Details the critical steps for safe electrical grounding of the tool.

Tile Saw Specific Safety Warnings

Specific safety guidelines and definitions unique to operating a tile saw.

Operational Safety Precautions

Covers safety advice on tool placement, water management, extension cords, and general operation.

Setup and Specifications

Vibration Safety

Discusses vibration risks and mitigation techniques for user health.

Product Specifications

Lists the technical ratings and dimensions of the tile saw.

Product Functions Overview

Identifies and illustrates the key components and features of the saw.

Assembly Instructions

Mounting the Saw

Instructions for securely attaching the tile saw to a stable surface.

Installing the Blade and Guard

Step-by-step guide for fitting the saw blade and blade guard.

Installing Accessories

Procedures for attaching the rip fence, miter gauge, and overflow drain.

Operating Instructions

Tool Setup and Reservoir Filling

Pre-operation checks, water filling, and work area preparation.

Cutting Procedures

Guides for performing cross cuts, diagonal cuts, miter cuts, and bevel cuts.

Maintenance and Troubleshooting

Cleaning, Maintenance, and Lubrication

Procedures for regular maintenance and cleaning of the tool.

Troubleshooting Guide

Solutions for common problems encountered during operation.

Parts and Diagram

Parts List

A comprehensive list of all parts with descriptions and quantities.

Assembly Diagram

Visual representation of how parts assemble together.

This document is the owner's manual and safety instructions for the Diamondback 7" Wet Benchtop Tile Saw, model 57087. It provides comprehensive information on the saw's functions, technical specifications, setup, operation, and maintenance, emphasizing safety throughout.

Function Description:

The Diamondback 7" Wet Benchtop Tile Saw is designed for cutting various tile and man-made masonry products. It operates as a wet saw, utilizing a water reservoir to keep the blade cool and minimize dust during cutting, which is crucial for extending blade life and ensuring cleaner cuts. The saw features a 7-inch blade and a 5/8-inch arbor size. It is equipped with a rip fence and miter gauge for precise straight and angled cuts, including cross cuts, 45° diagonal cuts, miter cuts, and bevel cuts (22.5° and 45°). A blade guard and riving knife are integrated to enhance safety during operation by preventing kickback and ensuring proper kerf maintenance. The saw's benchtop design makes it suitable for various work environments, and it includes a carrying handle for portability. A safety key is incorporated into the power switch, preventing unintentional starting and enhancing user safety.

Important Technical Specifications:

Electrical Rating: 120VAC / 60Hz / 6.5A
Motor No Load Speed: 3450 RPM
Max. Blade Diameter: 7"
Arbor Size: 5/8"
Power Cord: Equipped with a 3-prong grounding plug for 110-120 VAC grounded outlets.

Usage Features:

Safety Key: The power switch requires a safety key to operate, preventing accidental startup. The manual advises removing and storing the key separately after use, especially out of children's reach.
Wet Cutting System: Features a water reservoir with a fill line and an overflow drain. The water system keeps the blade cool and reduces dust, requiring the reservoir to be filled before each use and maintained above the minimum fill line during operation to prevent blade damage.
Rip Fence: Adjustable for setting desired cut widths, secured by a locking lever. It includes a scale for precise measurements.
Miter Gauge: Used for making angled cuts. It slides along the rip fence and can be adjusted to specific angles using an angle scale and secured with a gauge lock knob.
Bevel Table: Allows for bevel cuts at 22.5° and 45°. The table can be lifted, and bevel legs pulled out to rest on ledges at the far end of the reservoir to achieve these angles.
Blade Guard and Riving Knife: Essential safety components that must be in place and working correctly during all operations. The riving knife aligns with the saw blade to prevent the kerf from closing and causing kickback. The blade guard slides over the riving knife and is adjustable for height.
Workpiece Support: Emphasizes the importance of supporting the workpiece firmly against the table and fence at all times to prevent kickback and ensure accurate cuts. Freehand cutting is explicitly prohibited.
Extension Cord Guidelines: Provides a table for recommended minimum wire gauge for extension cords based on length and ampere rating to prevent power loss and overheating. It also advises using outdoor-rated, undamaged 3-wire extension cords with grounding plugs and receptacles.
Drip Loop: Instructions for positioning the saw and cord to create a drip loop, preventing water from reaching electrical outlets or connections.
GFCI Protection: Recommends using Ground Fault Circuit Interrupter (GFCI) protected circuits or outlets for added safety against electric shock.

Maintenance Features:

Pre-Use Inspection: Before each use, users are instructed to inspect the tool for loose hardware, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition affecting safe operation.
Post-Use Cleaning: After each use, external surfaces, rails, the water tray (including emptying sediment and water), and the pump filter and housing should be cleaned.
Dust Removal: Periodically, users should wear ANSI-approved safety goggles and NIOSH-approved breathing protection and use dry compressed air to blow dust out of the motor vents.
Blade Alignment: If the blade is out of alignment or the table does not slide smoothly, professional servicing by a qualified technician is recommended.
Cord Replacement: A damaged supply cord must be replaced only by a qualified service technician.
Troubleshooting Guide: Includes a table outlining common problems, possible causes, and likely solutions, such as checking power connections, replacing worn blades, and addressing motor issues.
General Maintenance: Emphasizes keeping tools sharp and clean, following lubrication instructions, and changing accessories as needed. It also warns against using damaged equipment and advises having problems corrected by a qualified technician if abnormal noise or vibration occurs.

Diamondback 57087 Specifications

General

Brand	Diamondback
Model	57087
Category	Saw
Language	English

Related product manuals