Diamondback 64684 - Operating Instructions; Installing Blade

Page 13;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 64684
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
I/*(,$"83%L8#$('4$"&8#
%K*,9%$.*%6MGLK6%LNJIKGFMG%EF;6GH%LM;IKNFGLIM%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*a$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
GIIT%E6G%PJ
GI%JK6!6MG%E6KLIPE%LMbPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%
G'(8%$.*%J&)*(%E)"$4.%&2%$.*%$&&7%&22%,89%'8/7'3%$.*%$&&7%2(&5%"$#%*7*4$("4,7%&'$7*$%
+*2&(*%/*(2&(5"83%,8V%/(&4*9'(*%"8%$."#%#*4$"&81
GI%JK6!6MG%E6KLIPE%LMbPKH-%
UI%MIG%IJ6KFG6%QLGX%FMH%RPFKU%ULEFST6U=%UFNFR6U=%IK%K6NI!6U1
L8#$,77"83%S7,9*
1. Unplug the saw.
2. Turn the Blade Guard Knob counterclockwise.
Open the Blade Guard to expose the Spindle.
3. Press and hold the Spindle Lock in. Loosen the
Spindle Nut counterclockwise and remove the
Nut, Outer Flange, and old Blade, if installed.
4. Leave the Inner Flange on the Spindle,
making sure the cupped side of the Flange
is facing the Tile Saw housing.
5. Wipe a drop of oil onto the Inner Flange
where it will contact the Blade.
QFKMLMRc%%GI%JK6!6MG%E6KLIPE%LMbPKH-%%%
Only use a smooth rim, wet cutting, 10″ Blade rated
$&%,$%7*,#$%d=ZZZ%KJN%&8%$."#%$&&71
Do not use a Blade that is too thick to allow Outer
Flange to engage with the flats on the Spindle.
Do not use a Blade that has openings, grooves, or teeth.
6. Slide the Blade (sold separately) onto
Spindle. Make sure that the Blade′s rotation
arrow points in the same direction as the
rotation arrow on the Blade Guard.
M&$*- The Saw is equipped with two Water
Nozzles to wet the Blade during operation. Make
sure holes in Nozzles face the Blade and that
Blade is positioned between the two Nozzles.
7. Place Outer Flange onto the Spindle.
The flats on the Outer Flange align with the
flats on the Spindle. Install with the cupped
side of the Outer Flange facing the blade.
8. Place Spindle Nut on Spindle. Press and hold
the Spindle Lock in. Wrench-tighten Spindle
Nut securely. Release the Spindle Lock.
9. Close the Blade Guard, and use
the Guard Knob to secure it.
S7,9*%
R',(9
Q,$*(%
M&ee7*
S7,9*
S7,9*%
R',(9%
Y8&+
E/"897*%
M'$
E/"897*%
M'$
E/"897*%
T&4_
Q(*84.%
I'$*(%
;7,83*
I'$*(%
;7,83*
L88*(%
;7,83*
L88*(%
;7,83*
S7,9*%L8#$,77,$"&8