Page 4 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 64684
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
R(&'89"83%L8#$('4$"&8#
%
GI%JK6!6MG%6T6OGKLO%EXIOY%FMU%U6FGX%;KIN%LMOIKK6OG%
RKIPMULMR%QLK6%OIMM6OGLIM%K6FU%FMU%;ITTIQ%GX6E6%LMEGKPOGLIME-
>>Z?>[Z%!FO%R(&'89*9%G&&7#-%G&&7#%)"$.%G.(**%J(&83%J7'3#
1. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.
3. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
4. Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.
5. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.
6. Repair or replace damaged or
worn cord immediately.
R(&'89"83%
J"8
>[B%!FO%\?J(&83%J7'3%,89%I'$7*$
]2&(%'/%$&%>[B%!FO%,89%'/%$&%>B%F^
7. This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above in
>[B%!FO%\?J(&83%J7'3%,89%I'$7*$. The tool has
a grounding plug that looks like the plug illustrated
above in >[B%!FO%\?J(&83%J7'3%,89%I'$7*$.
8. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.
9. Do not use an adapter to connect
this tool to a different outlet.
G"7*%E,)%E,2*$V%Q,(8"83#
;&(%H&'(%I)8%E,2*$V%K*,9%L8#$('4$"&8%
N,8',7%S*2&(*%I/*(,$"83%E,)
1. Wear eye protection.
2. Use saw-blade guard and spreader
for every operation for which it can be
used, including all through sawing.
3. Keep hands out of the line of saw blade.
4. Use an appropriate push-stick when required.
5. Know how to reduce risk of kickback.
6. Do not perform any operation freehand.
7. Never reach around or over saw blade.
8. Make sure the workpiece is supported
at all times while sawing.
9. To properly understand all safety warnings,
be familiar with the following safety
terms and equipment:
a. Featherboard – A block with “fingers” that hold
the workpiece against the fence while sawing.
b. Through-sawing – A cut made from one side of
a tile to the opposite side, without stopping.
c. Push-stick – A narrow strip of wood or other
soft material with a notch cut into one end
and which is used to push short pieces
of material through saws. It provides a
safe distance between the hands and the
cutting tool. Must be narrower than the cut
width to prevent contact with the blade.
d. Freehand – Feeding a workpiece through the
saw without using a fence or guided support
to guide it. MIG%F%EF;6%N6GXIU1
To Next Page
Loading...
