While battery operated:
• If AC power is removed while the logger is on, a rechargeable battery will
provide backup for up to 20 hours.
• The Logger will display “NO A/C” in the lower right corner of the display.
• The display will remain on for 2 minutes and will then turn off to conserve
battery power.
• To reactivate the display, press the On/Off button. The display will power
on, displaying the most recent data, for 2 minutes before turning the display
off. After 20 hours the logger must be powered via AC in order to turn on.
• The logger will continue to log data while operating on battery only power
while the display is off, for up to 20 hours.
• The logger will not sound an audible alarm when an alarm condition is
present while operating on battery power.
• The unit must run for 24 hours before the backup battery is fully charged.
NOTE: The logger is set to wrap when full. Depend
NOTE: The logger is set to wrap when full. DependNOTE: The logger is set to wrap when full. Depend
NOTE: The logger is set to wrap when full. Depending on the time graph
ing on the time graph ing on the time graph
ing on the time graph
interval and the duration of lost AC,
interval and the duration of lost AC, interval and the duration of lost AC,
interval and the duration of lost AC, older data will be lost.
older data will be lost.older data will be lost.
older data will be lost.
Wall Mounting
Wall MountingWall Mounting
Wall Mounting
Your Touchscreen includes a wall mount plate, two each: wall anchors, #4 screws.
Follow the steps below for proper placement:
• Whenever possible, mount plate to studs using #4 screws (included).
• If studs are not available:
o Use a 5/32 drill bit to drill 2 pilot holes.
o Gently tap wall anchors (included) into holes.
o Secure plate to wall using #4 screws (included).
Warranty
WarrantyWarranty
Warranty
Dickson warrants this line of instruments will be free from defects in material and
workmanship under normal use and service for a period of twelve months, after
delivery. This warranty does not cover routine calibration or battery replacement.
For Specifications and Technical Support, go to
http://www.dicksondata.com
http://www.dicksondata.comhttp://www.dicksondata.com
http://www.dicksondata.com
or contact us via telephone at 800.323.2448.
R24 07022012 V3
DICKSON
DICKSON DICKSON
DICKSON Touch
TouchTouch
Touchs
ss
screen Logger
creen Logger creen Logger
creen Logger
FT620/FT625/FT6
FT620/FT625/FT6FT620/FT625/FT6
FT620/FT625/FT63
33
30
00
0/
//
/FT640
FT640FT640
FT640/
//
/FT6
FT6FT6
FT645/
45/45/
45/FT660
FT660FT660
FT660
Getting Started
Getting StartedGetting Started
Getting Started
Your Color Touchs
Your Color TouchsYour Color Touchs
Your Color Touchscreen Logger includes the following
creen Logger includes the followingcreen Logger includes the following
creen Logger includes the following:
::
:
• AC Adapter
• Probe or Pod
• Certificate of Calibration
• Quick Start Manual
*
**
*SD
SD SD
SD Flash Memory Card
Flash Memory CardFlash Memory Card
Flash Memory Card,
, ,
, USB Cable and DicksonWa
USB Cable and DicksonWaUSB Cable and DicksonWa
USB Cable and DicksonWare
re re
re S
SS
So
oo
of
ff
ft
tt
tw
ww
wa
aa
ar
rr
re
ee
e
a
aa
ar
rr
re
ee
e
s
ss
so
oo
ol
ll
ld
dd
d
s
ss
se
ee
ep
pp
pa
aa
ar
rr
ra
aa
at
tt
te
ee
el
ll
ly
yy
y.
..
.
Presets
PresetsPresets
Presets
• Model: FT
FTFT
FT6
66
620/FT
20/FT20/FT
20/FT6
66
625/FT
25/FT25/FT
25/FT6
66
630
3030
30/FT
/FT/FT
/FT6
66
640/FT
40/FT40/FT
40/FT6
66
645
4545
45/FT
/FT/FT
/FT6
66
660
6060
60
Time Scale: 1 Hour / Sample every 6 sec
Temperature Range: 0 to 100
Unit of Measure: Deg. F
Alarm: OFF
Quick Start
Quick StartQuick Start
Quick Start
The Touch
The TouchThe Touch
The Touchs
ss
screen Logger is a computer
creen Logger is a computercreen Logger is a computer
creen Logger is a computer device and must be set and restarted
device and must be set and restarted device and must be set and restarted
device and must be set and restarted p
pp
pr
rr
ri
ii
io
oo
or
rr
r
t
tt
to
oo
o
use
useuse
use.
..
.
1) Plug the AC adapter into a standard electrical outlet, connect the logger to
the AC adapter and slide the power switch up to the “On” position.
2) Set Time: Press Menu Setup Set Time Save OK
3) Set Date: Press Menu Setup Set Date Save OK
4) Set Time Scale: Press Menu Set Scales Set Time Scales Save OK
5) Power off the logger, wait 10 seconds and power on the logger
6) Press Current to view current readings. The logger is ready for use when
readings are displayed. If no readings are displayed, repeat the above steps.
Logger Time:
Logger Time:Logger Time:
Logger Time: The logger does not automatically adjust for daylight savings. You
must manually adjust the logger time during the start and end of Daylight Savings.
Exporting Data:
Exporting Data:Exporting Data:
Exporting Data:
Saved data can be exported to and viewed in DicksonWare
• The logger must be CLEARED via DicksonWare 17.12 or greater prior to
logging and downloading data.
• Export data using the USB cable or Flash Memory Card. Open DicksonWare
to view exported data.
• When running
When runningWhen running
When running DicksonWare on a computer
DicksonWare on a computer DicksonWare on a computer
DicksonWare on a computer with Da
with Da with Da
with Day
yy
yl
ll
li
ii
ig
gg
gh
hh
ht
tt
t
S
SS
Sa
aa
av
vv
vi
ii
in
nn
ng
gg
gs
ss
s
s
ss
se
ee
et
tt
tt
tt
ti
ii
in
nn
ng
gg
gs
ss
s,
,,
,
adjust
adjust adjust
adjust the computer
the computer the computer
the computer as follows:
as follows:as follows:
as follows:
From Time & Date Settings:
To Next Page
Need help?
General
