EasyManua.ls Logo

DigiTech C8 User Manual

DigiTech C8
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
DigiTech Warranty
1. The warranty registration card must be mailed within ten days after purchase date to validate this warranty.
2. DigiTech warrants this product, when used solely within the U.S., to be free form defects in materials and workmanship under normal use
and service.
3. DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the prod-
uct is returned through the original dealer, where all parts and labor will be covered up to a period of one year. The company shall not be
liable for any consequential damage as a result of the product’s use in any circuit or assembly.
4. Proof-of-purchase is considered to be the burden of the customer.
5. DigiTech reserves the right to make changes in design, make additions to, or improvements upon this product without incurring any obliga-
tion to install the same on PRODUCTS PREVIOUSLY MANUFACTURED.
6. The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person to assume for
it any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or conse-
quential damages or form any delay in the performance of this warranty due to causes beyond their control.
DigiTech is a registered trademark of the Harman Music Group
DECLARATION OF CONFORMITY
Manufacturer’s Name: Digitech
Manufacturer’s Address: 8760 S. Sandy Parkway
Sandy, Utah 84070, USA
declares that the product
Product Name: Control 8 MIDI Controller
Product Options: All ( with a Class II power adapter that conforms to the requirements of
EN60065, EN60742, or equivalent).
conforms to the following product specifications:
Safety: EN 60065 (1993)
IEC63 (1985) with Amendments 1,2,3
EMC: EN 55013: (1990)
EN 55020: (1991)
Supplementary Information:
The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC as amended by directive 93/68/EEC.
Digitech
President of Digitech
8760 S. Sandy Parkway
Sandy, Utah 84070, USA
Effective: 2/27/98
European Contact: Your Local Digitech Sales and Service Office or
International Sales Office
3 Overlook Drive #4
Amherst, New Hampshire 03031, USA
Tel (603) 672-4244
Fax (603) 672-4246
DigiTech
8760 South Sandy Parkway - Sandy, Utah 84070 USA
Tel: (801) 566-8800 - Fax: (801) 566-7005
International Distribution
3 Overlook Drive Unit 4 - Amherst, New Hampshire - 03031 USA
Tel: (603) 672-4244 - Fax: (603) 672-4246
Control Eight 18-2214-B
User’s Guide
Please Visit Digitech on the World Wide Web at http://www.digitech.com
Question and Answer IconNeed help?

Do you have a question about the DigiTech C8 and is the answer not in the manual?

DigiTech C8 Specifications

General IconGeneral
Input Impedance1 MΩ
Output Impedance1 kΩ
EffectsChorus
Inputs1 x 1/4" Instrument
Power9V DC power supply

Summary

DigiTech Warranty

Declaration of Conformity

Introduction to DigiTech Control 8

Pedal Description

Provides details on the Control 8's LED display, pedals, MIDI jack, and power input.

Connection

Explains how to connect the Control 8 via MIDI and AC power for operation.

DigiTech Control 8 Operation

MIDI Channel Select

Guides on selecting the operating MIDI channel using footswitches and the display.

Continuous Controller Mode

Details on using the Control 8 as a continuous controller and switching modes.

Pedal CC Select

Instructions for selecting CC number values using footswitches for pedal control.

Program Selection / Program Mode

Explains how to select program changes, banks, and the display indicators.

Selecting Hopback Mode

Describes how to enable or disable the instant return to the previously selected footswitch value.

Pedal Calibration

Outlines the procedure for recalibrating the expression pedal for accurate performance.

Related product manuals