Operating Codes Continued
Page
22. Code 49
NAME BLK PRV OFF Private Name Block Disabled (Default) 8
23. Code 50
NBR INVITE SAVED 6
24. Code 51
NBR INVITED LIST Stored Invited list displayed 5
25. Code 52
B/AREA PAS SAVED 6
26. Code 53
B/AREA PASS LIST Stored Invited list displayed 5
27. Code 58
NAME BLK OOA ON Out of Area Name Block Enabled 8
28. Code 59
NAME BLK OOA OFF Out of Area Name Block Disabled (Default) 9
29. Code 60
NBR VIP SAVED 6
30. Code 61
NBR VIP LIST Stored VIP number list displayed 5
31. Code 70
SKIP 1ST RING (Default) 5
32. Code 71
PASS 1ST RING 6
33. Code 72
OPX CALL allowed on Line 9
34. Code 73
OPX CALL HANG UP (Default) 9
35. Code 74
PRIVATE ENABLED 9
36. Code 75
PRIVATE DISABLED (Default) 9
37. Code 76
OUT OF AREA -ON 9
38. Code 77 OUT OF AREA -OFF (Default) 9
39. Code 78
PBX ENABLED 9
40. Code 80
AFTER HOUR M OFF (Default) 10
41. Code 81
AFTER HOURS M ON 10
42. Code 82
ENTER START TIME 9
43. Code 83
ENTER END TIME 9
44. Code 84
SET MON-FRI ON 10
45. Code 85
SET MON-FRI OFF (Default) 10
46. Code 86
SET SAT-SUN ON 10
47. Code 87
SET SAT-SUN OFF (Default) 10
48. Code 88
MON SUN 24HRS ON 10
49. Code 90
DIAL DISPLAY NBR 10
50. Code 91
ASK FOR DIAL 1? (Default) 10
51. Code 92
DISPLAY CODES FUNCTION 11
52. Code 95
# * SET Time/Date - D/Time Enabled (Default) or D/Time Disabled User Set 10
53. Code 96
# * REG CALL INVITED Invite All Valid Numbers (Default) 10
54. Code 97
# * REG CALL DISABLE Block All Calls Except Invited 11
55. Code 98
# * ALL NBR DELETED 11
56. Code 98 [number] *
Delete specified number 11
57. Code 99 # *
DIGITONE DEFAULT On reset, operating codes return to default list 11
58. Last Call Remote Entry
Code * 1 # Invite, Code * 2 # Block, Code * 3 # VIP 12
Wildcarding (#)
When using the block or invite commands, you can use the # key to represent all numbers in a phone
number’s column. In the phone number ex. 894 555 1212, if you want to block or invite all numbers (0-
9) in a single column you would insert the # key in that column. Examples: To block all numbers (0-9) in
the last column, you would use 40 894 555 121# *. To invite all numbers in the exchange 679 and area
code 894, use 50 894 679 *. To block all numbers in the exchange 555 use: 20 555 *.
Last Call Remote Entry
You can enter the LAST caller into the Caller Lists by dialing * 1 # to Invite, * 2 # to Block, or * 3 #
for VIP after a call. This is useful when you have installed the DPB in a basement, phone closet and are
using cordless phones away from the base unit. After entering one of these dialed commands, either
through Phones connected to the TEL port or Extension phones, you will hear a confirmation beep in the
phone’s speaker. See the DPB display screen to verify entries when needed.
12
To Next Page
Loading...
