Dillon Precision Products Square Deal B

Questions and Answers

F
flynnjulieSep 23, 2025
What to do if primer is not dropping through magazine tube on Dillon Precision Products Industrial Equipment?
- M
  mark55Sep 23, 2025
  If a Primer is not “Dropping" through the Magazine Tube, perform a single primer drop test with the Magazine Tube out of the system. Hold the Mag Tube vertically with the tip resting on a flat surface. Drop one primer into the top of the tube, shiny side down. Gently pick up the tube. The Primer should be sitting on the flat surface. If not, check the tip for damage and or burrs on the semicircular "fingers." If no damage and the primer is caught in the “fingers”, gently and very lightly open the two "fingers." Try the test again. If still unsuccessful, replace the Tip and perform the test until successful.
J
jasonlongAug 25, 2025
How to fix inconsistent powder charges with Dillon Precision Products Industrial Equipment?
- K
  kkennedyAug 25, 2025
  Inconsistent powder charges can occur for several reasons. To resolve this, consider the following: 1. Ensure the Failsafe Return Rod Blue Wing Nut is tight enough to fully retract the Powder Bar. When the handle is fully down, tighten the Blue Wing Nut until two business cards just slip between the coils of the spring. Adjust the Powder Die height to obtain full Powder Bar travel. 2. Make sure the powder has settled in the hopper by cycling more powder charges until stable. 3. Verify you are using the correct size Powder Bar for your requirements and replace it if necessary. 4. Ensure the Powder Measure is not loose on the Powder Die by tightening the clamping screws. 5. Try slowing down your cycling. 6. Check if the Small Powder Bar Spacer Plug is missing and replace it if needed.
O
Omar HickmanAug 25, 2025
What to do if I have scratched cases with Dillon Precision Products Industrial Equipment?
- M
  Mary FarleyAug 26, 2025
  Scratched cases can result from a few issues: * Brass residue buildup in the Size Die (even carbide) over time, especially if cases aren't cleaned well. Remove hardened brass buildup using Red 3M Scotch Brite wrapped around a wood mandrel, chucked in a drill motor, or use Sweets 7.62 Solvent, ensuring all residue is removed afterward. * Dirty brass can cause scratches. * New brass may have burrs.
J
johnharperAug 27, 2025
Why is the handle movement difficult on my Dillon Precision Products Industrial Equipment?
- M
  Mrs. Angela RobertsAug 27, 2025
  Difficult handle movement can stem from several causes: 1. Powder or other debris may be causing a jamming of moving parts. 2. Link Arm and/or Pins may be worn or galled, so clean and relube them. 3. The Main Shaft or Wave Bearings may be worn, sticky, or dirty, so clean and lubricate with 30 wt. oil, avoiding spray lubes like WD-40. 4. The Priming System may not be aligned with the Platform/Shellplate, so realign it.
T
Tracy CurtisAug 27, 2025
How to resolve difficult indexing on Dillon Precision Products Industrial Equipment?
- D
  Derrick GonzalezAug 27, 2025
  Difficult indexing can be caused by several factors: 1. Ensure the Shellplate Bolt is tight. 2. Check for the correct size Locator Buttons. 3. Remove any sticky gunk or debris under the Shellplate by removing the Shellplate and cleaning with alcohol. 4. Make sure the Ejector wire is not dragging on the Shellplate by adjusting the Ejector Wire height to clear the Shellplate.
C
Christopher MichaelSep 14, 2025
What can cause unusual indentation in seated primer for Dillon Precision Products Industrial Equipment?
- J
  joan84Sep 14, 2025
  An unusual indentation in the face of a seated primer can be caused by powder granules on top of the Primer Punch Face imprinting into the Primer. Clean off or blow out spilled powder granules.
J
Jamie ReyesSep 12, 2025
What to do if bullets are falling through the case mouth on Dillon Precision Products Industrial Equipment?
- A
  Aaron DanielSep 12, 2025
  If bullets are falling through the case mouth or cartridge neck: 1. Ensure that the case was sized. 2. Verify that the bullet diameter is correct.
C
Christopher OrtegaSep 13, 2025
What causes powder funnel sticking in case for Dillon Precision Products Industrial Equipment?
- K
  kaiserkimSep 13, 2025
  If the Powder Funnel is sticking in the case, polish the end to remove any brass buildup and lightly lube with Case Lube.
Z
zparksSep 4, 2025
How to fix erratic flaring on Dillon Precision Products Industrial Equipment?
- S
  Sharon GonzalezSep 4, 2025
  Erratic flaring (too much or too little) can be due to: 1. Variation in case length. Measure cases and trim or discard those out of spec. 2. The handle not moving all the way down on each cycle. 3. Using the wrong Powder Funnel for that caliber. 4. Improper Powder Die adjustment. 5. The Powder Measure being loose on the Powder Die.
K
Kyle ThomasSep 2, 2025
What causes cases to stick in size die on Dillon Precision Products Industrial Equipment?
- C
  carly79Sep 2, 2025
  Cases sticking or stuck in the Size Die can be attributed to: 1. Insufficient lubrication on the case. 2. An overpressure or "blown-out" case, indicating the case is out of spec/oversize. 3. The alcohol from Dillon Case Lube not being given enough time to evaporate.

Summary

Mandatory Safety Precautions

Basic Risk of Reloading and Safety

Discusses inherent dangers and safe usage of the reloading process.

Mandatory User Safety Requirements

Outlines essential safety rules for operating the Square Deal.

Square Deal Limited Lifetime Warranty

Square Deal Shipping Contents

Items from Top Foam Layer

Lists items to remove from the top layer of the shipping box.

Items from Second Foam Layer

Lists items to remove from the second layer of the shipping box.

Square Deal Assembly Guide

Optional Equipment for the Square Deal “B”

Dillon Square Deal Reloading Stations and Configurations

Station 1-Deprime and Size Case

Performs depriming and sizing of the cartridge case.

Station 2-Seat Primer, Bell Case Mouth and Dispense Powder

Seats primer, bells case mouth, and dispenses powder.

Station 3-Seat Bullet

Seats the bullet into the cartridge case.

Station 4-Crimp Bullet and Eject Completed Cartridge

Crimps the bullet and ejects the finished cartridge.

Setup Procedures for Square Deal B

Blue Friction Plate in Toolhead Assembly

Describes the Blue Friction Plate's role in the Toolhead Assembly.

Station 1-Sizing and Depriming

Station 2 a-Primer Feeding, Seating, Case Belling and Powder Dispensing

8.5 Powder Measure Setup-Case Mouth Expanding and Powder Dispensing

Powder Charge Bars

Details the Small and Large Powder Charge Bars included with the system.

Automatic Powder Measure System Adjustments

Outlines the three key adjustments for the automatic powder measure.

Case Mouth Belling (Flaring)

Explains how to properly flare the case mouth for bullet seating.

Powder Charge Weight Adjustment

Guides adjustment of powder dispensed for accurate reloading.

8.6 Station 3-Bullet Seating Setup Cartridge Overall Length (COAL)

Seating Die Installation

Details the installation process for the bullet seating die.

Seating Die Adjustment

Explains how to adjust the seating die for correct cartridge overall length.

8.7 Station 4-Bullet Crimping

Taper Crimping for Semi-Auto Cartridges

Explains taper crimping for semi-auto cartridges.

Pistol Crimp Die Installation

Details the installation of the pistol crimp die.

Pistol Crimp Die Adjustment

Guides adjustment of the pistol crimp die.

9. Conversion and Replacement Procedures

Caliber Conversion Procedure

Provides steps for converting the reloader to different calibers.

Shellplate Conversion Procedure

Step-by-step guide to replacing the shellplate.

Primer Size Conversion

Instructions for changing the primer size components.

Die Caliber Conversion Procedure

Details the process of converting dies for different calibers.

9.4. Powder Measure Conversion Procedure-Small to Large Bar

9.5. Replacing the Depriming pin

10. Adjustment Procedures

Shellplate to Primer Feed;Toolhead Alignment and Indexing

Aligning and adjusting the shellplate, primer feed, and toolhead.

Adjusting Primer Drop Alignment

Fine-tuning the primer drop alignment in the feed assembly.

11. Troubleshooting Guide Square Deal “B”

12. Cleaning and Lubricating the Square Deal “B”

Link Arm Bearing Cleaning and Lubrication

Procedure for cleaning and lubricating link arm bearings and wave bearings.

General Cleanliness

Guidance on maintaining general cleanliness of the reloading system.

13. Exploded Views and Parts Identifier

Main Assembly

Diagram and parts list for the main assembly of the reloader.

Frame and Lower Assembly

Diagram and parts list for the frame and lower assembly.

Typical Toolhead Assembly

Diagram and parts list for the toolhead assembly.

Automatic Primer Assembly

Diagram and parts list for the automatic primer assembly.

Primer Slide Assemblies

Diagram and parts list for primer slide assemblies.

Primer Early Warning System

Diagram and parts list for the primer early warning system.

Automatic Powder System

Diagram and parts list for the automatic powder system.

14. Reloading Basics

Clean Brass Is Required Before Reloading

Explains the importance of cleaning brass before the reloading process.

Lubricating Brass

Provides instructions for properly lubricating brass cases before sizing.

Head Space-Case Sizing

Explains the concept of headspace and its importance in case sizing.

Documentation

Emphasizes the importance of record-keeping for reloading parameters.

15. Primer Basics

16. Notes