ELECTRICAL CONNECTION
WARNING THIS APPLIANCE MUST BE EARTHED
DO NOT use an extension lead or multi-plug adaptor when
connecting this product to the mains. Connection through these
devices could lead to risk of overloading, overheating and even fire at
the extension lead or adaptor due to inadequate connection quality.
This heater must be used on an AC (~) supply only and the voltage
marked on the heater must correspond to the supply voltage. This
heater is fitted with a plug incorporating a 10 amp fuse. When
replacing the fuse, a 10 amp fuse approved by ASTA to BS 1362
must be used.
If the plug is damaged or not suitable for your socket outlets in your
home, the plug must be cut off and an appropriate one fitted. A plug
cut off from a mains lead will give a shock hazard if inserted into
a 13 amp socket elsewhere in the house. To avoid this, it should be
disposed of immedaitely.
NOTE: The fuse cover of a non-rewirable plug must be fitted when
changing the fuse. Should the cover bocome lost, the plug must be
replaced.
IMPORTANT: The wires in this mains lead are coloured in accordance
with the following code:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead may not
correspond with the coloured markings in your plug,
proceed as follows:
Connect the BROWN wire to the terminal marked ‘L’ or
coloured RED. Connect the BLUE wire to the terminal
marked ‘N’ or coloured BLACK. Note: ‘L’ or ‘N’ must not
be connected to the EARTH terminal marked ‘E’ or ‘’ or
coloured GREEN or GREEN AND YELLOW.
If in doubt, consult your electrician.
Assembly and Positioning
FITTING THE CASTORS
WARNING The radiator must only be operated
with the wheels and castors fitted and in the
upright position.
The castors must be fitted to the control panel and on
the bracket between the last and second last fin on the
opposite end, as shown in Fig.1.
To fit the castors, turn the radiator upside down on a
carpet or other soft surface to avoid damage
WARNING : THE RADIATOR IS HEAVY – ENSURE THAT
IT IS SUPPORTED TO PREVENT IT FROM TOPPLING. Ask
a second person to help with this if necessary.
To fit the castors, position the castor plates (A) in position
and secure using the wing bolts (B). there are guides
to ensure the correct positioning and orientation of the
caster plate.
Return the radiator to the correct orientation so it rests
on the castors. The product is now ready for use.
A
B
Fig. 1
POSITIONING THE HEATER
Select the position for the heater ensuring there is clearance
from any furniture and fittin gs of at least 300mm above the
heater and 150mm each side and 300mm from the control and
end panel. We recommend maximising the clearance where
possible.
Model Description
Power
(W)
ECR15
7 fin, thermostat, three heat settings &
neon
1500
ECR20
9 fin, thermostat, three heat settings &
neon
2000
GENERAL
The radiator is designed for operation on an AC electricity
supply, and is suitable for use in domestic dwellings and similar
indoor locations.
The radiator is fitted with castors and a handle for ease of
movement. A rotary selector switch provide the ability to
choose an available heat output and an adjustable thermostat
enables the room temperature to be controlled accordingly. It
is supplied with a cord and plug and is ready for use once the
castors have been correctly fitted.
Thermostat
Off/Heat selection swit
Neon Indicator
Timer - Ti(e) models
Cable Wrap
Fig. 2
combustible materials such as drapes and other
furnishings clear from the front, sides and rear of
the heater. Do not use heater to dry your laundry.
DO ENSURE that the mains lead cannot be tripped
over.
DO NOT operate the radiator with the mains lead
overhanging the fins.
If the radiator is tipped over, unplug it and allow it
to cool before standing it back up.
DO NOT pull, carry or move the appliance using the
power cable.
The supply cord should be uncoiled before use.
This instruction leaflet belongs to the appliance and
must be kept in a safe place. If changing owners,
the leaflet must be surrendered to the new owner.
Models & General Information
To Next Page
Loading...
