To Next PageTo Next PageWhy is the display not working on my Dino-Power X20 Paint Sprayer?
If your Dino-Power Paint Sprayer operates but there is no display, the display is either damaged or has a bad connection. Check the connection and replace the display if necessary.
What does error code E02 mean on my Dino-Power X20 Paint Sprayer?
If your Dino-Power Paint Sprayer displays error code E02, it indicates a communication failure. Check the signal line between the pressure sensor and the PCB.
What does error code E03 mean on my Dino-Power X20 Paint Sprayer?
If your Dino-Power Paint Sprayer displays error code E03, it indicates a pressure sensor failure. Check the pressure sensor for poor contact or damage.
What does error code E04 mean on my Dino-Power Paint Sprayer display?
If your Dino-Power Paint Sprayer displays error code E04, it indicates a motor and PCB communication failure or a mechanical fault. Check the signal line between the motor and PCB, and inspect the mechanical components for any obstructions.
What does error code E07 mean on my Dino-Power X20 Paint Sprayer?
If your Dino-Power Paint Sprayer displays error code E07, it indicates high pressure in cleaning mode. Reduce the pressure when cleaning.
What does error code E08 mean on my Dino-Power X20?
If your Dino-Power Paint Sprayer displays error code E08, it indicates a low line voltage. Check the power supply.
What to do if my Dino-Power Paint Sprayer motor doesn't run?
If your Dino-Power Paint Sprayer's motor doesn't run, and the pump doesn't cycle, even when the power switch is on and it's plugged in, there are several potential causes: * The pressure may be set too low. Try turning the pressure control knob clockwise to increase the pressure setting. * The electric outlet might not be providing power. Test the outlet with another device or try a different outlet. Also, check and reset the building circuit breaker or replace the fuse. * The extension cord or sprayer electric cord could be damaged. Replace the extension cord or check the sprayer's cord for broken insulation or wires, replacing it if damaged. * Paint or water may be frozen or hardened in the pump. Unplug the sprayer and place it in a warm area to thaw. Do not attempt to start the...
Why my Dino-Power X20 starts but won't draw paint?
If your Dino-Power Paint Sprayer starts up but doesn't draw in paint, consider these possible causes and solutions: * The unit may not be primed or has lost prime. Replace the prime unit. * There might be no paint, or the suction tube isn't fully immersed in the paint. Ensure the suction tube is completely immersed in the paint. * The suction set filter could be clogged. Clean the filter. * The suction tube might be loose at the inlet valve. Clean the connection and tighten it. * The inlet valve could be leaking. Clean the inlet valve, ensuring the ball seat isn't nicked or worn and that the ball seats well; then reassemble the valve. * The pump packings could be worn. Replace the pump packings. * The piston rod might be worn or damaged. Clean or replace it.
What does error code E15 mean on my Dino-Power X20?
Error code E15 on your Dino-Power Paint Sprayer means static electricity is interfering with the communication inside the electronical control board. Turn off the power, and after the display screen is completely off, turn the power back on. If the problem persists, replace the electronical control board.
What does error code E14 mean on my Dino-Power Paint Sprayer display?
Error code E14 on your Dino-Power Paint Sprayer indicates too low voltage and using too small a tip size at the same time. Check the voltage and change to a bigger tip size. You should also check if the inner parts of the fluid pump are damaged, and if so, change the fluid pump.
General| Brand | Dino-Power |
|---|---|
| Model | X20 |
| Category | Paint Sprayer |
| Language | English |
Warnings about flammable materials, static electricity, and ventilation.
Instructions for safe electrical connection and usage to prevent shock.
Guidance on high-pressure spray hazards and preventing injection injuries.
Warning about fluid incompatibility with aluminum parts.
Safety guidelines to prevent injury from improper equipment operation.
Caution regarding pinch and cut hazards from moving machinery parts.
Warning about hot equipment surfaces during and after operation.
Precautions for handling toxic fluids and fumes to prevent injury.
Mandatory protective gear for safe operation and servicing.
Engaging the trigger lock to prevent accidental spraying.
Steps to safely relieve pressure before servicing or transport.
