How to improve paint coverage with my Dino-Power DP-X3?
If the paint coverage is inadequate when using the Dino-Power Paint Sprayer, move the gun slower. Choose a spray tip with a larger hole size and a narrower fan. Make sure the gun is close enough to the surface.
What to do if Dino-Power DP-X3 gun stopped spraying while trigger is pulled?
If your Dino-Power Paint Sprayer gun stops spraying while the trigger is pulled, it could be due to a clogged spray tip. Clear the spray tip clog. Also, the sprayer might have lost prime. Refer to the troubleshooting section regarding a sprayer that runs but doesn't prime or loses prime during use.
Why is paint running down the wall when using Dino-Power?
If paint runs or sags when sprayed with your Dino-Power Paint Sprayer, it's likely being applied too thickly. Try moving the gun faster. Also, try using a spray tip with a smaller hole size and wider fan, and ensure the gun is far enough from the surface.
Why is coverage inadequate when using Dino-Power DP-X3 Paint Sprayer?
If coverage is inadequate when spraying with the Dino-Power Paint Sprayer, the material might be going on too thinly. Try moving the gun slower. You may need to choose a spray tip with a larger hole size and narrower fan, and make sure the gun is close enough to the surface.
Why does fan pattern varies dramatically while spraying with Dino-Power?
If the fan pattern varies dramatically while spraying with your Dino-Power Paint Sprayer, the pressure control switch might be worn and causing excessive pressure variation. Take the sprayer to a DINO-POWER authorized service center.
What to do if Dino-Power DP-X3 Paint Sprayer is primed, but can not achieve good spray pattern?
If your Dino-Power Paint Sprayer is primed but the spray pattern is poor: * **Clogged spray tip:** Clear the clog. * **Reversible spray tip in UNCLOG position:** Rotate to the SPRAY position. * **Debris in paint:** Strain the paint. * **Low pressure:** Adjust the pressure control knob. * **Clogged spray gun fluid filter:** Clean or replace the filter. * **Incorrect spray tip size:** Replace the tip with the correct size. * **Worn spray tip:** Replace the tip. * **Worn or missing spray tip gasket and seal:** Replace the gasket and seal. * **Clogged inlet strainer or suction tube not immersed:** Clean the strainer and ensure the suction tube is immersed in paint. * **Incorrect extension cord:** Replace the cord. * **Worn or clogged pump valves:** Clean and reinstall th...
Why can't I trigger my Dino-Power airless spray gun?
If you cannot trigger the airless spray gun of your Dino-Power Paint Sprayer, rotate the trigger lock to disengage it.
Why does my Dino-Power Paint Sprayer run, but not prime?
If your Dino-Power Paint Sprayer runs but doesn't prime, it could be due to several reasons: * **Inlet valve check ball stuck:** Press the PushPrime button. * **Prime/Spray valve in SPRAY position:** Turn the valve to the PRIME position until paint exits the drain tube. * **Pump not primed with flushing fluid:** Prime the pump with oil or water-based flushing fluid. * **Debris in paint:** Strain the paint. * **Thick paint:** Turn the ON/OFF switch on and off several times. * **Clogged inlet strainer or suction tube not immersed:** Clean the strainer and ensure the suction tube is immersed in paint. * **Dirty inlet valve check ball or seat:** Clean or replace the ball and seat. * **Leaking suction tube:** Inspect for cracks or leaks. * **Stuck outlet valve check ball:** U...
What to do if paint sags when using Dino-Power Paint Sprayer?
If paint is running down the wall or sagging when sprayed with your Dino-Power Paint Sprayer, move the gun faster. Choose a spray tip with a smaller hole size and a wider fan. Ensure the gun is far enough from the surface.
What to do if Dino-Power motor is hot and runs intermittently?
If your Dino-Power Paint Sprayer motor is hot and runs intermittently, it may automatically shut off due to excessive heat. To fix this: * Ensure vent holes are clear of obstructions and overspray, keeping the sprayer open to air. * Replace any extension cord that is too long or not a heavy enough gauge. * If using an electrical generator, ensure it has a proper voltage regulator. * If the motor needs to be replaced, take the sprayer to an authorized retailer, distributor, or service center.
General| Type | Airless Paint Sprayer |
|---|---|
| Power Source | Electric |
| Max Pressure | 3000 PSI |
| Voltage | 110V/60Hz or 220V/50Hz (depending on the region) |
| Frequency | 60 Hz |
To Next Page
