Dirt Devil REBEL34 - Vacuum Cleaning; Maintaining the Appliance

NOTE:
You can also use the suction nozzles without the
telescopic tube as necessary. To do so, connect
the required accessories directly to the handle
(Fig.
9
).
1
Connect the required accessory to the handle or
the telescopic tube (Fig.
9
).
2
Make sure that the
accessory is securely connected. ➔ The appliance
can be connected.
Connecting the appliance
CAUTION!
If the red marking is visible (Fig.
6
/
1
), retract
the connection cord by pressing the cord rewind
button to pull in the cord up to the yellow mark
(Fig.
6
/
2
) (Fig.
7
). Otherwise, the connection
cord might be damaged.
1
Pull the cable out of the appliance (Fig.
5
).
2
Insert the plug into a mains socket.
Vacuum cleaning
Flexible vacuum-cleaning
1
Connect the required accessories >”Using the ac-
cessories” on page 16.
2
Connect the appliance
>”Connecting the appliance” on page 18.
3
To switch
on the appliance, press the ON/OFF button (Fig.
8
).
➔ The appliance vacuums at full suction power.
4
To reduce the suction power, open the bypass
vent as required >”Regulating the suction power”
on page 17.
5
To switch o the appliance, press
the ON/OFF button again (Fig.
8
). ➔ The appliance
switches o.
6
Close the bypass vent (Fig.
1
/
14
) so
that the appliance operates with full suction power
when vacuum-cleaning the next time.
Regulating the suction power
1
To reduce the suction power, slide the bypass vent
open (Fig.
11
).
2
To increase the suction power, slide
the bypass vent closed again (Fig.
11
).
Storing the appliance
NOTE:
If necessary, use the holding clip on the suction
hose (Fig.
1
/
12
) to attach accessories.
1
Switch o the appliance and pull the plug from the
socket.
2
Push the cord rewind button (Fig.
1
/
7
)
until the cord has been fully rewound (Fig.
7
).
3
Hang the telescopic oor nozzle or parquet nozzle
(connected to the telescopic tube or handle) in the
parking bracket (Fig.
1
/
8
) (Fig.
12
).
Maintaining the appliance
Emptying the dust bin
1
Switch o the appliance and pull the plug from
the socket.
2
Press the dust bin release catch
(Fig.
1
/
6
) and remove the dust bin from its console
in the appliance (Fig.
13
).
3
Place dust bin closely
above a waste bin and release the dust bin (Fig.
14
).
4
Dispose of the contents of the dust bin in a waste
bin. Gently tap out the dust bin to remove any soil-
ing.
5
Close the emptied dust bin.
6
Re-insert the
dust bin into its console in the appliance so that you
feel it click into place.
Cleaning the separator and lter
NOTE:
The appliance, the separator and the pre-motor
lter should be cleaned regularly in order to
maintain the suction power. Empty and clean the
dust bin at the latest when the cleaning/empty-
ing display lights up (Fig.
13
).
1
Remove the dust bin from the appliance, >”Emp-
tying the dust bin” on page 18.
2
Push the upper
dust bin cover release (Fig.
1
/
1
).
3
Remove the
pre-motor lter (Fig.
15
).
4
Remove the separator,
together with the separator cover, from the dust bin
(Fig.
16
).
5
Release the separator cover (Fig.
17
).
6
Remove the cover from the separator (Fig.
18
).
7
Remove the separator and dispose of the con-
tent in a waste bin.
8
Rinse the pre-motor lter and
the separator out thoroughly under running water.
9
Leave the cleaned parts to dry completely for at
least 24 h.
10
Insert the separator cover into the sep-
arator (Fig.
19
).
11
Insert the separator, together with
the separator cover, into the dust bin (Fig.
20
).
12
Place the pre-motor lter on the dust bin (Fig.
21
).
13
Close the dust bin cover.
14
Re-insert the dust bin
into its console on the appliance body. You must be
able to feel the dust bin click into place.
EN
17