2
1
●
Use only the supplied charger to charge the battery. Only charge the battery when it is powered off. DO NOT charge the Intelligent Flight
Battery and remote controller at the same time.
●
When charging is complete, the battery will automatically power off and the Status LED will change from red to green.
8
Creativity Unleashed
www.dji.com
INSPIRE 1
PRO
4
3
1
3
2
7. Installing the Camera
1
Ensure the camear body cap, the lens cap and rear cap are removed. Align the two Lens Mount Indexes on the
camera body and camera lens, and insert the camera lens into the body of the camera.
Rotate the camera lens clockwise until you hear a click.
Rotate the Lens Lock anticlockwise to lock it.
Mount the Balancing Ring (or a filter) and the Lens Hood. Insert the Micro SD card.
2
3
1
●
Always set the camera lens to AF mode.
●
While holding down the Lens Release Button, rotate the camera lens anticlockwise to detach it.
●
Mount only a lens filter or Balancing Ring on the camera.
Rotate the Lens Lock anticlockwise to tighten the junction between the lens and camera body
when using the camera.
Rotate the Lens Lock clockwise to loosen the junction between the lens and camera body when
attaching and detaching the camera.
4
Balancing Ring or Filter
Lens Hood
4. Charging
3. Check Battery Levels
●
For the best user experience, please use mobile devices with iOS 8.0 (or higher) and Android 4.1.2 (or higher).
The tutorial videos
DJI GO app
Watch the tutorial videos at www.dji.com or in the DJI GO app.
2. Watch the Tutorial Videos
1. Download the DJI GO App
Search ‘DJI GO’ on the App Store or Google Play and
download the app to your mobile device.
Watch the video tutorials on the official DJI website and read the following documents before using your Inspire 1 Pro for the first
time:
Inspire 1 Pro Quick Start Guide, Inspire 1 Pro Intelligent Flight Battery Safety Guidelines, Inspire 1 Pro Safety Guidelines
and Disclaimer, Inspire 1 Pro In the Box, Inspire 1 Pro User Manual.
3
Power Outlet
100-240V
●
Intelligent Flight Battery must be fully charged before
using it for the first time.
Low
High
Battery Level
High
Low
Battery Level
●
Press once to check the battery level.
●
Press twice and hold to turn on/off.
●
If you have purchased the dual remote controller version, you must use the Master remote controller to deactivate Travel Mode.
●
Toggling up and down at least four times to change aircraft back into Travel Mode.
5. Preparing the Aircraft
2
1
Insert the Battery Power on the remote
controller and the aircraft
Change aircraft to
Landing Mode
Toggle up and
down at least
four times
Gimbal Connector
Mounting Place
Gimbal Lock
Left stick / Up (Slowly)
Start / Stop the motors
OR
The App’s
RTH Button
Travel Mode
Landing Mode
6. Preparing the Remote Controller
Tilt the Mobile Device Holder to the desired position then adjust
the antennas as shown. The strength of the remote controller
signal is different when the antenna position is different.
The transmission signal between the aircraft and remote controller will
perform best when within the optimal transmission range. If the signal is
weak, fly the aircraft closer to you to achieve optimal signal performance.
Strong Weak
U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
Left Stick
Right Stick
1
5
6
7
8
1
2
5
6
3
4
7
●
While returning home, its
altitude can be adjusted by
the user to avoid
obstructions.
Before taking off, make sure the aircraft
status bar in the DJI GO app shows “Safe
to Fly (GPS)”. Otherwise, the aircraft cannot
hover in place and record the Home Point.
11. Flight
● Manual Take - off & Landing：
Safe to Fly (GPS)
● Auto Taking - Off & Landing:
Tap and confirm your selection. The aircraft will automatically take off, retract its
landing gear, and hover at 1.2 meters after you tap and confirm Auto Take-off.
1
Using INSPIRE 1 PRO
●
You can set the remote controller to different modes using the DJI GO app.
●
Do not use other 2.4GHz devices at the same time to avoid signal interference.
8. Mounting the Gimbal and Camera
10. Remote Controller Operation
The remote controller is by default set to Mode 2 ( throttle controlled by the left-hand stick ).
Adjust the tilt angle of camera by using the Gimbal Dial.
●
When not in P mode, the Inspire 1 Pro will only maintain altitude, not position, and will drift
with wind or user inputs. Return to Home is not available in F mode.
●
Ensure the aircraft is fully charged when use with the Zenmuse X5, as power suddenly
drops may bring dangerous.
Press the button to release the clamp.
Place your device onto the clamp and adjust the clamp to
hold it securely.
Connect your mobile device to the remote controller with a
USB cable.
Rotate the Gimbal Lock to the unlocked position.
Align the key on the damping plate with the slot on the gimbal's pan motor.
While aligning the white lines on the Gimbal Connector and Gimbal Lock,
insert the Gimbal Connector.
Rotate the Gimbal Lock to the locked position.
1
Move the Flight Mode Switch to the right to select P mode. ( P mode is Positioning mode, A mode
is ATTI mode, and the F mode is Function mode. )
Power on the remote controller.
Power on the aircraft and wait for the self-check to complete. Do not move the aircraft during the
self-check.
Ensure the remote controller is linked to the aircraft before flight. Re-link the remote controller to the
aircraft if it fails to connect. Refer to the INSPIRE 1 PRO User Manual on how to link.
Ensure the remote controller and your mobile device are connected with a USB cable. Launch the
DJI GO app when connecting to the aircraft for the first time, and follow the instructions within the app.
Launch the DJI GO app and tap “Camera”. Ensure the aircraft is functioning normally by completing
the Checklist.Beginner Mode is enabled by default when you launch the DJI GO app for the first
time. The aircraft’s altitude and flight distance is restricted when flying in Beginner Mode. We
recommend you fly in Beginner Mode when using the aircraft for the first time. You may disable
Beginner Mode in the settings page of the DJI GO app.
Calibrate the compass by tapping the Aircraft Status Bar in the app and selecting “Calibrate”. Then
follow the on-screen instructions.
Installing the 1345T Propellers: Attach the propellers with white arrows onto the motors with white arrows,
and attach the propellers with red arrows onto the motors with red arrows. To attach the propeller, rotate
the propeller lock to align the arrows on the mounting plate and propeller lock. Attach the propeller and
then rotate the propeller lock until the arrows on the propeller and propeller lock are aligned.
9. Preparing for Flight
Place the aircraft on a flat surface, in an open space, with the back facing you.
Ensure to power off the aircraft.
Appendix
Aircraft
Status Indicator Description
Slowly: Safe to fly,GPS working
Slowly: P-ATTI or ATTI
Quickly: Not connected
to remote controller
Slowly: Low battery level warning
Quickly: Critical low battery level warning
Solid: Critical error
Blinking Alternately:
Compass calibration required
Double: Vision Positioning
System working, no GPS
X2
www.dji.com/product/inspire-1-pro-and-raw
Gently pull the left (throttle) stick down to lower the
aircraft until it touches the ground. Pull both sticks to the
bottom inside corners to stop the motors.
After flight, change the aircraft back into Travel Mode. Do
not attempt this at the beach, over grass, or over
monochromatic carpet. Then place the aircraft on a flat
surface and remove the gimbal and camera for transport.
● Return to Home
Start the motors by pulling both control sticks to the bottom inside (or outside)
corners. Release the sticks once the motors start. Slowly push the left (throttle)
stick up to take off. Once in the air, toggle the Transformation Switch up to
raise the landing gear.
RC normal but not connected to aircraft.
RC normal and connected to aircraft.
RC Slave Mode and connected to aircraft.
B-B-B... Aircraft low battery warning /
RC error.
B—B—... RC idle for 5 minutes.
Using the Camera
●
Adjust the camera parameters using the
Camera Settings Dial on the remote controller
or through the DJI GO app. Press the Shutter
Button/Video Record Button to capture
photos or record videos.
●
Adjust the tilt of the gimbal using the Gimbal
Dial.
●
Download photos and video from the SD card
to your mobile device through the DJI GO
app. You may also use a SD card reader to
export files to your PC.
1. Press and hold the return home
button until the LED surrounding the
button is blinking white, and the
return home procedure is in process.
Press once to stop the procedure.
2. The DJI GO app notifies users to take
action when the battery level falls to a
specified threshold. This warning
threshold can be set within the DJI
GO app. The aircraft will land
immediately when it reaches Critical
Low Battery Level Warning.
3. Failsafe: The Inspire 1 Pro will enter
RTH mode if remote controller signal
is lost.
Gimbal Dial
( In the Camera screen of the DJI GO app )
Tap and confirm your selection. The landing gear will lower and the aircraft will
automatically land.
●
It is highly recommended that you only take off when the Aircraft Status bar is green.
●
The aircraft cannot take off if the Critical Low Battery Warning is active.
●
The Intelligent Flight Battery must warm-up if the outside temperature is low. A warning will
display in the DJI GO app.
●
Rotating propellers can be dangerous. Do not start the motors when there are people nearby
and always fly in a wide open area.
●
Never stop the motors during flight. Always keep your hands on the remote controller so long as
the motor is still spinning. Power off the aircraft before turning off the remote controller after landing.
©2015 DJI. All Rights Reserved
Designed by DJI. Printed in China.
Learn more information from:
Left stick / Down (Slowly)
RTH Button
Connecting the Master remote controller to the Slave remote
controller: On the Master remote controller, launch the DJI GO
app and go to the Camera page. Then tap on the top of
your screen to enter the remote controller settings window.
Tap “Activate Master/Slave Mode”and select “Master”. Then
enter your desired connection password for the “Slave”
remote controller. On the Slave remote controller, select
“Slave “ and tap “Search” to find the Master remote controller.
Select the “Master” remote controller from the “Master RC
List” and input the connection password.
DJI GO
App
Toggle the
Transformation
Switch up
If you have purchased an Inspire 1 Pro with dual remote
controllers, the Master remote controller will connect to the aircraft
automatically when powered on. Master/Slave mode is disabled
by default. Activate it and set it up through the DJI GO app.
Remote Controller Status LED
B... Send RTH command to aircraft.
BB .. .. Aircraft returning to Home Point.
Initiate RTH procedure.
Video downlink error.
Using DJI Focus
Use DJI Focus to remotely adjust the camera lens
(e.g. continuous manual focus). Refer to "Inspire 1
Pro User Manual" or "DJI FOCUS User Manual" for
more information.
RC Slave Mode and not connected to aircraft.
Key
Slot
To Next Page
Loading...
