EasyManua.ls Logo

Dolmar MS-335.4 C - User Manual

Dolmar MS-335.4 C
80 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
MS-335.4 U/MS-335.4 C
GB String Trimmer
F Débroussailleuse thermique
LS Desbrozadora
Important:
Read this instruction manual carefully before putting the String Trimmer into operation and strictly observe
the safety regulations!
Preserve instruction manual carefully!
Important :
Lisez attentivement ce manuel d’instructions avant d’utiliser la débroussailleuse thermique et respectez
scrupuleusement les règlements de sécurité!
Conservez précieusement ce manuel d’instructions!
Importante:
Lea esta manual de instrucciones con atención antes de utilizar la desbrozadora y ¡observe estrictamente
las regulaciones de seguridad!
¡Conserve cuidadosamente su manual de instrucciones!
ORIGINAL INSTRUCTION MANUAL
MODE D’EMPLOI ORIGINAL
MANUAL ORIGINAL DE INSTRUCCIONES
MS-335.4 U MS-335.4 C

Table of Contents

Other manuals for Dolmar MS-335.4 C

Preview: Original Instruction Manual
Original Instruction Manual196 pages

Questions and Answers

  • B
    betty75Aug 10, 2025
    What to do if Dolmar MS-335.4 C Brush Cutter engine stops soon?
    • J
      Janice McguireAug 10, 2025
      If your Dolmar Brush Cutter's engine stops soon after starting, it could be due to: * Insufficient warm-up. Perform a warm-up operation. * Choke lever is set to “CLOSE” although engine is warmed up. Set it to “OPEN”. * Clogged fuel filter. Clean the filter. * Contaminated or clogged air cleaner. Clean the air cleaner.
  • L
    Leslie HardinAug 15, 2025
    What to do if Dolmar MS-335.4 C Brush Cutter main unit vibrates abnormally?
    • M
      Marissa SmithAug 16, 2025
      If the main unit of your Dolmar Brush Cutter vibrates abnormally, check for the following: * A broken, bent, or worn cutter blade. Replace the cutter blade. * A loosened cutter blade-tightening nut. Tighten it securely. * A shifted convex part of cutter blade and cutter blade support fitting. Attach them securely.
  • R
    Robert BennettAug 21, 2025
    What to do if Dolmar MS-335.4 C blade does not rotate?
    • R
      Robin HallAug 21, 2025
      If the cutter blade of your Dolmar Brush Cutter does not rotate, consider these possible causes: * Loosened cutter blade-tightening nut. Tighten the nut securely. * Twigs caught by cutter blade or dispersion- preventing cover. Remove any foreign matter.
  • J
    jrobinsonAug 27, 2025
    What to do if Dolmar MS-335.4 C engine does not stop?
    • J
      jcrossAug 27, 2025
      If the engine of your Dolmar Brush Cutter does not stop, check for a detached connector and attach it securely.
  • L
    Lindsey SaundersAug 30, 2025
    What to do if Dolmar Brush Cutter blade does not stop immediately?
    • C
      cgonzalezAug 30, 2025
      If the cutter blade on your Dolmar Brush Cutter does not stop immediately, it may be due to: * High idling rotation. Adjust it. * Detached throttle wire. Attach it securely.
  • J
    Jennifer FoleyNov 5, 2025
    Why Dolmar Brush Cutter engine does not start?
    • R
      Rachel PhillipsNov 5, 2025
      The Dolmar Brush Cutter engine might fail to start due to several reasons: * Failure to operate primer pump. Push it 7 to 10 times. * Low pulling speed of starter rope. Pull it strongly. * Lack of fuel. Add fuel. * Clogged fuel filter. Clean it. * Broken fuel tube. Straighten it. * Deteriorated fuel. Replace it with new fuel, as deteriorated fuel makes starting more difficult (recommended replacement: 1 month). * Excessive suction of fuel. Set throttle lever from medium speed to high speed, and pull starter handle until engine starts. Once engine starts, cutter blade starts rotating, so pay full attention to cutter blade. If engine will not start still, remove spark plug, make electrode dry, and reassemble them as they originally are. Then, start as specified. * Detached ...

Dolmar MS-335.4 C Specifications

General IconGeneral
BrandDolmar
ModelMS-335.4 C
CategoryBrush Cutter
LanguageEnglish

Related product manuals